background image

                                                                                                Rev. 01/2011  

LIMITED WARRANTY  

Vestil Manufacturing Corporation (“Vestil”) warrants this product to be free of defects in material and workmanship  

during the warranty period. 

Our warranty obligation is to provide

 

a replacement for a defective original part

if

 

the part  is 

covered by the warranty

after we receive a proper request from the warrantee (you) for warranty service

.  

Who may request service?  

Only a warrantee may request service.  

You are a warrantee 

if

 

you purchased the product from Vestil or from an  

authorized distributor AND Vestil has been fully paid.  

What is an “original part”?  

An original part is a part 

used to make the product as shipped

 to the warrantee.  

What is a “proper request”?  

A request for warranty service is proper if Vestil receives: 1) a photocopy of the Customer Invoice that displays the  

shipping date; AND 2) a written request for warranty service including your name and phone number.  Send requests  by 

any of the following methods:  
      Mail 

Phone 

Fax 

Email         

Vestil Manufacturing Corporation 

(260) 665-7586  

(260) 665-1339 

[email protected]

2999 North Wayne Street, PO Box 507                           

Angola, IN 46703   

 

 

             

 

  

In the written request, list the parts believed to be defective and include the address where replacements should be  

delivered.  

What is covered under the warranty?

  

After Vestil receives your request for warranty service, an authorized representative will contact you to determine  

whether your claim is covered by the warranty.  Before providing warranty service, Vestil may require you to send the  

entire product, or just the defective part or parts, to its facility in Angola, IN. The warranty covers defects in the  following 

original

 dynamic components: motors, hydraulic pumps, electronic controllers, switches and cylinders.  It  also covers 

defects in 

original

 parts that wear under normal usage conditions (“wearing parts”): bearings, hoses,  wheels, seals, 

brushes, batteries, and the battery charger.  

How long is the warranty period?

  

The warranty period for original dynamic components is 1 year.  For wearing parts, the warranty period is 90 days.   Both 

warranty periods begin on the date when Vestil ships the product to the warrantee.  If the product was purchased  from an 

authorized distributor, the periods began when the distributor shipped the product.  Vestil may extend the  warranty period 

for products shipped from authorized distributors by 

up to

 30 days to account for shipping time. 

  

If a defective part is covered by the warranty, what will Vestil do to correct the problem?

  

Vestil will provide an appropriate replacement for any 

covered

 part.  An authorized representative of Vestil will contact  

you to discuss your claim.  

What is not covered by the warranty?  

1. Labor;  

2. Freight;   

3.  Occurrence of any of the following, which automatically voids the warranty:  

 Product misuse;  

  Negligent operation or repair;  

  Corrosion or use in corrosive conditions;  

  Inadequate or improper maintenance;  

  Damage sustained during shipping;  

  Accidents involving the product;  

  Unauthorized modifications:  DO NOT modify the product IN ANY WAY without first receiving  written 

authorization from Vestil.  Modification(s) might make the product unsafe to use or might  cause 

excessive and/or abnormal wear.  

Do any other warranties apply to the product?  

Vestil Manufacturing Corp.

 

makes no other express warranties. All implied warranties are disclaimed to the extent  

allowed by law. Any implied warranty not disclaimed is limited in scope to the terms of this Limited Warranty.   

12  

Summary of Contents for EHLTG













Reviews: