manualshive.com logo in svg

VESTEL MB120 DS, Service Manual

Share
Download
VESTEL MB120 DS Service Manual Download Page 59

58 
 

3.

 

Select the corresponding COM port and click File to load the fw hex file. 

 

 

4.

 

Press “ Program MCU “ to enter ICP mode. Then restart the DS product. 

 

 

5.

 

 When you finish all of settings, press “ Program MCU “ again to program the firmware. 

6.

 

When you program the firmware successfully, EP Console would appear a message of OK . 

 

 

7.

 

Finally restart the DS product.  
 

If you see fail, please reset monitor and try program again. 

18.

 

TROUBLESHOOTING 

A.

 

NO BACKLIGHT PROBLEM 

 

Problem:

 If product is working, led is normal and there is no picture and backlight on the panel. 

 

Possible causes:

 Backlight pin, dimming pin, backlight supply, stby on/off pin  

 
 

BACKLIGHT_ON/OFF pin should be high when the backlight is ON. R89 must be low when the backlight 

is OFF. If  it is a problem, please check Q10 and the panel cables. Also it can be tested in TP137 on main board 

Summary of Contents for MB120 DS





















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands