background image

7

1.  Ioniser: reduces static build up
2.  Slider arm base : mechanism to move the cutting arm
3.  Tracking arm: arm to hold cutting head and apply correct pressure
4.  Tracking arm weight: adjusts cutting pressure
5.  Slider cam: locks the cutting arm in place
6. Release 

lever

7.  Manual rotation wheel: to set the position of the cutting arm in the correct place on the vinyl blank
8.  Cutting head: Vestax proprietary design high quality stereo cutting head
9.  Tracking on/off switch
10.  Recording level volume control: to adjust the level of the incoming signal
11.  Heater current meter: visual display of the level of heat applied to the cutting stylus
12.  Heater current adjustment control: adjusts the level of the heat applied to the cutting stylus.
13.  VU level meters: a display of the input level signal left and right
14.  Vinyl blank holder: secures blank disc to platter
15. Blank disc
16.  Pitch control adjuster: adjusts pitch of p/- 10% , only applicable when quartz lock is disengaged.
17.  Quartz lock switch: locks pitch
18.  Speed select switch: selects the speed – 33 1/3 rpm  or 45 rpm.  LED displays 45rpm.
19. Start/stop switch
20.  Playback arm height adjustment screw
21.  Playback arm counter weight
22.  Playback arm headshell
23.  Playback arm armrest
24. Playback arm
25.  Heavy duty carrying handles
26.  Center spindle on turntable platter
27. Turntable platter

Summary of Contents for VRX-2000

















Reviews: