background image

Subject to modifications.

© Vestamatic GmbH

1/10

G

H O M E  · VL-SMI-230-45

Art.-Nr.: 

8900 001 GB 3117 A04  •  Vestamatic GmbH  •  Dohrweg 27  •  D-41066 Mönchengladbach 

 •  www.vestamatic.com

VL-SMI-230-45

Vestaline

SMI-Line motors

Installation and Operating Instructions

VL-SMI-230-45/10Nm

 

Art.-no.: 01066291

VL-SMI-230-45/20Nm

 

Art.-no.: 01066301

VL-SMI-230-45/30Nm

 

Art.-no.: 01066311

VL-SMI-230-45/50Nm

 

Art.-no.: 01066321

Vestaline motors for controlling roller shutters.

G

H O M E

8900 001 GB 3117 A04

1. Safety precautions

WARNING!
Important safety information.

Follow these instructions to ensure the 

safety of persons. The instructions must 

be stored.

 

– Contact a professional electrician to install 

the motor, be cause the motor requires a 

power supply of 230VAC, 50 Hz.

 

– Check the motor for signs of mechanical 

damage after un packing. If you notice 

any shipping damage, do not start up the 

motor and notify your supplier immedi-

ately.

 

– The motor should only be used for the 

purpose specified by the manufacturer 

(refer to the operating instructions). Any 

 changes or modifications thereof are not 

permissible and will result in loss of all 

warranty claims.

 

– Technical data can be found on the type 

label of the tubular motor.

 

– If the motor cannot be operated without 

presenting a hazard, it must be switched 

off and prevented from being switched 

on unintentionally.

 

– When performing work on the windows, 

motor or connected shades, protect 

them against unauthorised or uninten-

tional operation.

Ä

CONTENTS

1.  Safety precautions (safety measures)
2.  Short description (identification of products)
3.  Scope of delivery
4.  Intended use
5.  Technical data
6.  Standard Motor Interface
7.  Installation, Assembly, Disassembly
8.  Troubleshooting
9.  Warranty
10. Maintenance
11. Disposal of waste
12. Service / Contact
13. Declaration of conformity

 

– Moving parts of the motor installed un-

der 2.5 m above the floor level should be 

protected.

 

– This device is not intended for use by 

persons (including children) with reduced 

physical, sensory or mental abilities or 

lack of experience and / or lack of knowl-

edge, unless they are supervised by a 

person responsible for their safety, or re-

ceived instructions on how the device is 

to be used.

 

– Children should be supervised to ensure 

that they do not play with the device.

 

– Children are not allowed, to play with 

fixed controls. Keep remotes away from 

children.

 

– The installation has to be checked fre-

quently for imbalance or of signs of wear, 

damaged cables or springs, if applicable.

 

– Automatically controlled awnings have 

to be disconnected from the supply net-

work, e. g. if maintenance work has to be 

done close to them.

 

– Before the motor is installed, all un-

needed wires must be removed and all 

devices which are not required for actua-

tion with a power drive must be put out of 

operation.

 

– The actuating element of a hand release 

is to be installed at a height of less than 

1.8 m.

 

– The mains cable of this device cannot be 

replaced. If the mains cable is damaged, 

the device has to be discarded.

Summary of Contents for 01066291











Reviews: