background image

 

The Motion Sensor back cover has 2 hollowed 

break-out areas

. When the device is properly installed, if an intruder forcibly removes 

the Motion Sensor from mounted location, the break-away areas will break off from the back cover and remain attached to the 
mounting surface while the device main body is removed, activating the tamper switch. 

 

L

L

e

e

a

a

r

r

n

n

i

i

n

n

g

g

 

 

a

a

n

n

d

d

 

 

I

I

n

n

s

s

t

t

a

a

l

l

l

l

a

a

t

t

i

i

o

o

n

n

 

 

 

 

G

G

e

e

t

t

t

t

i

i

n

n

g

g

 

 

S

S

t

t

a

a

r

r

t

t

e

e

d

d

 

 

1.  Orient and insert the battery according to polarity.

 

 

2.  The Red Transmitter LED will begin to flash for 30 seconds to indicate the Motion Sensor is warming up. During the warming up 

period, the Motion Sensor will not be activated. It is recommended that you stay away from the detection area during this time. After 
the warming-up period, the Red will turn off and the Motion Sensor will enter normal 
operation.

 

 

3.  Put the Control Panel into learning mode; refer to Control Panel manual for detail.

 

 

4.  Press the Learn/Test Button to transmit signal to panel.

 

 

5.  If the panel receives signal from Motion Sensor, it will display sensor info accordingly. Refer 

to your Control Panel to complete the learn-in process.

 

 

6.  After the Motion sensor is learnt-in, put the Control Panel into “Walk Test” mode, hold the 

sensor in the desired location, and press the Test Switch to confirm this location is within 
signal range of the Control Panel.

 

 

7.  When you are satisfied with the chosen location, you can proceed with Installaiton.

 

 

 

 

M

M

o

o

u

u

n

n

t

t

i

i

n

n

g

g

 

 

M

M

e

e

t

t

h

h

o

o

d

d

 

 

  The Motion sensor is designed to be mounted on either a flat surface or in a corner situation 

with fixing screws and plugs provided. 

  The base has knockouts, where the plastic is thinner, for mounting purpose. Two knockouts 

are located on the back for surface fixing and four knockouts on the sides for corner fixing. 

  For IRM-23B corner mounting, a triangular bracket is provided to add Back Tamper Protection. 

The bracket also includes two knockouts to mount on the wall. 

  For IRM-23B surface mounting, an optional rotating bracket is provided for users to adjust the 

range of detection. With the rotating bracket, the IRM-23 can be rotated 80 degrees 
horizontally and 70 degrees vertically to provide optimal coverage. 

 

Corner mounting for IRM-23A: 

I. 

Detach the base and cover assembly by using a screwdriver to loosen the bottom 
fixing screw. 

II. 

Break through the four corner knockouts. 

III.  Using the four holes as a template, drill holes in the surface of the corner. 

IV.  Insert the wall plugs. 

V. 

Screw the base into the wall plugs. 

VI.  Fit the base onto the cover. 

VII.  Tighten the bottom fixing screw. 

 

Corner mounting for IRM-23B: 

I. 

Break through the knockouts on the 

triangular bracket

II. 

Using the two holes as a template, drill holes in the surface of the corner. 

III.  Insert the wall plugs 

IV.  Screw the bracket into the wall plugs 

V. Locate 

the 

Bracket Insertion Holes

 and fit the holes onto the 

Bracket Insertion Hooks

. Fitting 

the sensor onto the bracket should compress the Tamper switch onto the 

Tamper Compression 

Protrusion

 on the bracket. 

 

Surface mounting: 

I. 

Detach the base and cover assembly by using a screwdriver to loosen the bottom fixing screw. 

II. 

Break through the knockouts on the inside of base. 

III.  Using the holes as a template, drill holes in the surface. 

IV.  Insert the wall plugs if fixing it into plaster or brick. 

V. 

Screw the base into the wall plugs. 

VI.  Fit the base onto the cover. 

VII.  Tighten the bottom fixing screw. 

 

Surface mounting with rotating bracket (optional item, sold separately) for IRM-23B: 

The rotating bracket can be mounted on the wall with provides screws.   

I. 

Screw the rotating bracket into the wall. 

II.  Fit the 3 hooks of the rotating bracket into the 3 holes of the base accordingly. 

III.  Rotate the bracket for the proper range of detection and tighten the fixing screw.   

 

 

I

I

n

n

s

s

t

t

a

a

l

l

l

l

a

a

t

t

i

i

o

o

n

n

 

 

  Decide on the location of the Motion Sensor and if it is to be corner or surface mounted. 

  After the installation site is selected, follow the steps described above to mount the Motion Sensor. 

  Press the Test Switch to enter Test Mode. Walk around the protected area noting when the LED lights up 

and check that the detection coverage is adequate. 

  When detection coverage is found to be satisfying, installation is now completed. 

 

 

Bottom Fixing Screw

Summary of Contents for IRM-23 Series

Page 1: ...Yes IRM 23A SSL 2 x AA L91 Lithium batteries Internal No IRMP 23A SSL 2 x AA L91 Lithium batteries Internal Yes IRM 23B SSL 2 x AA L91 Lithium batteries Exposed No IRMP 23B SSL 2 x AA L91 Lithium batteries Exposed Yes P Pa ar rt ts s I Id de en nt ti if fi ic ca at ti io on n Front Internal Internal Back AA battery CR123A battery 1 1 T Tr ra an ns sm mi it tt te er r L LE ED D R Re ed d The LED li...

Page 2: ... od de e The Microwave Test Mode is for microwave range test only Use the JP3 Jumper to enable Microwave Test Mode When the Motion Sensor is under Microwave Test Mode PIR detection is disabled the Microwave Transmitter will be activated to repeatedly send microwave signal for movement detection When the Motion Sensor detects movement under Microwave Test Mode the Microwave Blue LED will light up b...

Page 3: ...rovided for users to adjust the range of detection With the rotating bracket the IRM 23 can be rotated 80 degrees horizontally and 70 degrees vertically to provide optimal coverage Corner mounting for IRM 23A I Detach the base and cover assembly by using a screwdriver to loosen the bottom fixing screw II Break through the four corner knockouts III Using the four holes as a template drill holes in ...

Page 4: ...nment factors When IRM 23 is mounted with rotating bracket it will not have the regular detection area as in the above diagram or the typical pet immue range It is recommended to install the Motion Sensor in the following locations Mount where the animals cannot come to the detection area by climbing on furniture or other objects Avoid aiming the sensor at stairways where the animals can climb on ...

Reviews: