background image

20 

 Operation

 

ALARM LAMPS 

 

H.V. Alarm (High voltage alarm lamp) 

The lamp lights in green when the high voltage transformer emits 
properly the high voltage. If the piezoelectric transformer detects 
an overload and shuts down the operation, the high-voltage alarm 
lamp will light up in red. 
When the H.V. lamp lights in red, 
1) Immediately unplug the power cable or pull out the wires from 

terminals. 

 

2) Remove the fan cover and visually inspect around the electrode needles. If foreign particles are 

adhered to the needles, refer to Cleaning Procedure and clean the needles.   

 

Fan Alarm (Fan lock alarm lamp) 

The lamp lights in green when the fan operates properly.   
Fan lock alarm lamp lights in red when the fan motor stops rotating.   
When fan lock alarm lamp lights in red, 
1) Unplug the power cable or pull out the wires from terminals. 
2) Remove the fan cover and visually inspect the fan. 

If foreign particles or objects are adhered to the fan, remove them, switch on the power again and make 
sure that the lamp is off. 

*If the alarm lamp light in red again even though the causes are resolved, contact the supplier for 
servicing to avoid accidents. 
* Immediately after turning on the power, there is a moment that the fan lamp glows red.   

This is not a malfunction. 

When externally outputting the alarm signal 

The lights and other external alarm devices can be operated by alarm signal output. 
Abnormal High Voltage alarm output: 
Connecting a load to the input/output terminal # 1 and # 2 
Fan Lock alarm output: 
Connecting a load to the input/output terminal # 3 and # 4 

 

Circuit diagram 

Abnormal High Voltage alarm output 

Abnormal High Voltage alarm output GND 

Fan Lock alarm output 

Fan Lock alarm output GND 

Photo coupler: SHARP PC817 

Filter (Option) 

Fan filter is available, depending on the applications. 
1)  Loosen  with  a  Philips  screwdriver  the  screws  (4 
pcs.) which fix the fan on the backside. 
2)  Replace  metal  Finger  Guard  with  a  resin  Finger 

Guard  of  Filter  set,  and  fix  the  resin  Finger  Guard 
with screws. 

3) Mount filter with a filter cover. 

 
 

 

Summary of Contents for Stat Clean F-120R-E













Reviews: