manualshive.com logo in svg

VESPA PX 125 150 euro 2, Workshop Manual

Share
Download
VESPA PX 125 150 euro 2 Workshop Manual Download Page 84

Front brake calliper

Removal

−

 Detach the brake hose from the calliper using a

container to collect the fluid.

−

 Remove the fasteners shown in the figure.

Refitting

−

 When refitting, tighten the nuts to the prescribed torque.

−

 Bleed the system.

N.B.

* Safety tightenings

IN ORDER TO ENSURE THE CORRECT TIGHTENING TORQUE, LUBRICATE NUTS BEFORE AS-
SEMBLY.

Locking torques (N*m)

Pipe - calliper fitting

 

15÷25

 

Calliper fixing screw*

 

20÷25

Front brake disc

Removal

−

 Remove the rear wheel by loosening the 5 fas-

teners.

−

 Remove the wheel hub.

−

 Loosen the 5 disc fasteners.

Refitting

−

 When refitting, correctly position the disc, observing the direction of rotation (see figure) and apply

medium thread-lock.

Braking system

Vespa PX 125 150 Euro 2

BRAK SYS - 84

Summary of Contents for PX 125 150 euro 2















































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands