background image

14

ORIGINAL INSTRUCTIONS

VES  Andover  Ltd  Eagle  Close  Chandlers  Ford  Ind.  Est  Eastleigh  Hampshire  SO53  4NF
Tel:  08448  156060    Fax:  02380  261204    E-mail:  [email protected]  Web:  www.ves.co.uk

               Acoustic Supply Unit

Installation,  Operation  and  Maintenance  Manual

®

Maintainance

6

Important

Warning

Before attempting to carry out any work on our units, all accompanying documentation
including warning labels on the unit must be referenced.
Should it be necessary to remove any component, ensure that these are resecured into position
once reinstalled. It is critical that after any maintenance work has been conducted that all
components removed/replaced be refitted correctly by a competent engineer.

When accessing the unit ensure the access panels/lids are handled/opened in a controlled
manner so as to avoid damage to the unit or injury to personnel. This is particularly important
with bottom access units.

Care should be taken with larger unit lid removal as this may need to be undertaken by more
than one person.

Caution

Before attempting to carry out any maintenance work, investigative or repair work on our units,
the unit 

MUST BE COMPLETELY ISOLATED 

from its electrical supply. Ensure a minimum of two

minutes after electrical disconnection before removing access panels. This will allow any moving
parts to come to a rest. Care should also be taken when accessing external units as the wind and
elements may cause moving parts to ‘windmill’.

Plug Connector

locking/Unlocking

Fig. 

22

Fan alignment

Fig. 

21

fan impellor

inlet eye

Summary of Contents for 0051-1


















Reviews: