background image

1

ORIGINAL INSTRUCTIONS

VES  Andover  Ltd  Eagle  Close  Chandlers  Ford  Ind.  Est  Eastleigh  Hampshire  SO53  4NF
Tel:  08448  156060    Fax:  02380  261204    E-mail:  [email protected]  Web:  www.ves.co.uk

               Acoustic Supply Unit

Installation,  Operation  and  Maintenance  Manual

®

VES Ref. ID.1086

Issue D

May 2015

This manual must be read in full before Installation, Operation and Maintenance of the units
supplied.

Please ensure that this document is passed to the end user. This manual forms an integral part
of the product and should be kept for the working life of the product. Additional copies of this
and supporting documents are available by contacting VES or by visiting 

www.ves.co.uk

 and

following the 'Information Centre' link.

The following symbols used within this document refer to potential dangers, advice for safe
operation or important points of reference

Indicates hazards associated with electric current and high voltages

Indicates hazards that require safety advice for personnel or potential unit/property damage

Indicates important information

page

Introduction

1

Nomenclature

2

Receipt of Goods & Handling

3

Installation

3

Standard Wiring & Fan Installation

7

Maintenance

14

The 

Colourfan acoustic

 supply series is a range of centrifugal supply units, direct driven with

duties up to 3m³/s. 

Suitable for plant-room, ceiling void and external locations.  

As standard,

each unit will have been supplied with either pre-wired fitted controls or pre-wired to an
isolator. 

The standard ambient operating temperature of the unit is -20 to +35°C.

For further technical details regarding dimensions and weights, contact VES on 

08448 15 60 60

,

quoting the sales order (SO) number and the unit type as found on the unit nameplate, or
alternatively visit 

www.ves.co.uk

.

Contents

Important

Introduction

1
2
3
4
5
6

1

Warning

Caution

Important

Summary of Contents for 0051-1


















Reviews: