background image

590-1509-501A

3

Avocent® AcS800 AdvAnced conSole SyStem

Mounting Installation Guide

raCK mouNtINg

NotE: 

The rack mounting kit is  

optional and is not included with the  
Avocent® ACS800 Advanced Console 
System. For details on how to purchase 
the rack mounting kit, contact your Vertiv 
representative. 

overview

The rack mounting bracket kit contains 
two brackets and a 1U rack shelf. Either 
bracket may be used as left or right 
bracket. 

1.  attaching the brackets  

to the console system

Remove the screws and brackets 
from the ACS800 Advanced 
Console System Wall Mount 
Accessory Kit. Position each 

bracket so its slotted flange is 

located along the bottom edge and 
its slotted face is positioned under 
the console system. Secure the 
mounting brackets to the console 

system using two (2) 6-32 panhead 
screws per bracket.

 

2.  attaching the console system  

to the shelf. 

Place the console system upside 
down on a work surface. Remove 
the rack mount shelf from the 

accessory kit box and place it 

upside down on top of the console 
system. Align the countersink screw 
holes on the shelf with the mating 
holes in the slotted brackets on the 
console system. Secure the console 
system to the shelf with two (2) 

6-32 flathead screws for each 

bracket. 

3.  Securing the power cords

Plug the power cord into the 
console system. Slip the supplied 
cable retention tie-wrap through 
the hardware adjacent to the power 
connector. Align the power cord 
with the hardware and loosely 
capture with the tie-wrap. Ensure 

sufficient slack exists between the 

plug and the cable attachment 
hardware, and cinch the  
tie-wrap to secure the power cord. 

4.  Installing the console system  

into the rack

Place the power supply on the read 
of the shelf behind the console 
system, then place the shelf in the 
desired 1U rack space and secure it 
with two (2) rack mounting screws 

in each shelf ear. Confirm the shelf 

is level and does not interfere with 
adjacent equipment, then tighten 
the screws. 

NotE: 

Rack mounting screws are not 

provided with the rack mounting kit. 
Ensure you use screws appropriate for 
your rack. 

Summary of Contents for Avocent ACS800

Page 1: ...tem using two 2 6 32 panhead screws per bracket 2 Attaching the DIN clips to the installed wall bracket Using the supplied screws attach the DIN clips to the bottom sides of each wall bracket Be sure to orient the clips as shown in the image 3 Attaching the appliance to the DIN rail Position the appliance so that the top of each DIN clip rests on the top edge of the DIN rail Push the bottom of the...

Page 2: ...re the mounting brackets to the console system using two 2 6 32 panhead screws per bracket 2 Mounting the brackets to a plywood wall Using the slots on the bracket as a guide mark the holes on the wall where the brackets are to be fastened A minimum of two holes for each bracket should be marked Use a 1 8 inch drill bit to drill guide holes at the marked positions Secure each bracket to the plywoo...

Page 3: ...ount shelf from the accessory kit box and place it upside down on top of the console system Align the countersink screw holes on the shelf with the mating holes in the slotted brackets on the console system Secure the console system to the shelf with two 2 6 32 flathead screws for each bracket 3 Securing the power cords Plug the power cord into the console system Slip the supplied cable retention ...

Page 4: ...names and logos referred to are trade names trademarks or registered trademarks of their respective owners While every precaution has been taken to ensure accuracy and completeness herein Vertiv Co assumes no responsibility and disclaims all liability for damages resulting from use of this information or for any errors or omissions Specifications are subject to change without notice 590 1509 501A ...

Reviews: