manualshive.com logo in svg

Vertex Wireless VW400 Series, User Manual

Share
Download
Vertex Wireless VW400 Series User Manual Download Page 28

28 | 

p a g e

 

2)

 

Fail to input the proper Pin number 

If you fail up to three times to input proper PIN code, 
the Authentication would be automatically into PUK 
code authentication. At this time you have 10 times to 
enter PUK code. If you fail up to 10 times to enter proper 
PUK code, you can’t use your UIM card any more. In that 
case consult your service provider. 
 

4.2.

 

Connecting to the Internet 
 

4.2.1

 

Connect

 

First, connect the modem into the PC then double-click the 
Connection Manager icon on the PC. If VW400 is inserted 
correctly, the LED on the Modem is blinking from Red to Blue. 
Once the modem is ready, CONNECT button will be enabled. 
Click the CONNECT button to be connected to the internet. 
Once the connection is completed, CONNECT button will be 
changed to DISCONNECT button   
 

4.2.2

 

Disconnect

 

Click the Disconnect button to be disconnected from the 
connection. Once the disconnection is completed, 
DISCONNECT button will be changed to CONNECT button 

 

 

Summary of Contents for VW400 Series


































Reviews:

No comments

Brands by name

Popular brands

Load more brands