manualshive.com logo in svg

Vertex Wireless VW400 Series, User Manual

Share
Download
Vertex Wireless VW400 Series User Manual Download Page 12

12 | 

p a g e

 

1.6.

 

Desktop installation 

Before you select a location to place VW400, you must read “For your safety” section in the first part of this manual. 
You can place it on the flat surface area such as above ground, on the walls, or table. 
1.    Connect the antenna to VW400 and locate it as far as it can reach 
     

* Note : finger-tighten the antenna. 

2.    Connect a wire telephone to VW400 using phone cord 
3.    Connect the barrel connector of the power supply to DC Adaptor   
4.    Plug the DC Adaptor into the power supply. 
5.    Plug the DC Adaptor into an appropriate power outlet. 
6.    Check signal strength moving the antenna until you find the best signal possible. 

(See 2.1 LED Status Indicator section) 

7.    If you use Data Service or PC FAX Service, connect your data cable to the Data port located at the side of VW400. 
8.    If you use G3 FAX machine, connect your line cord of G3 FAX to the RJ-11port located at the side of VW400.

 

Summary of Contents for VW400 Series


































Reviews:

No comments

Brands by name

Popular brands

Load more brands