manualshive.com logo in svg

VersaLogic VL-EPU-3311, Hardware Reference Manual

Share
Download
VersaLogic VL-EPU-3311 Hardware Reference Manual Download Page 47

VL-EPU-3311 Reference Manual 

47 

 

Network Interfaces 

The Osprey provides two Intel I210-IT Gigabit Ethernet controllers.  The controller provides a 
standard IEEE 802.3 Ethernet interface for 1000Base-T, 100Base-TX, and 10Base-T 
applications.  The I210-IT Ethernet controller auto-negotiates connection speed.  Drivers are 
readily available to support a variety of operating systems.  For more information on this device, 
refer to the 

Intel I210 Ethernet Controller datasheet

. 

 

Integrator’s Note:  

Ethernet Port 1 supports network boot; Port 0 does not. 

Ethernet Connector 

The Ethernet connector provides access to the Ethernet ports 0 and 1.  The connector uses IEC 
61000-4-2-rated TVS components to help protect against ESD damage.  Figure 24 shows the 
location and pin orientation of the Ethernet connector. 

 

 

Figure 24.  Location and Pin Orientation of the Ethernet Connector 

8 

Summary of Contents for VL-EPU-3311





































































Reviews:

No comments

Brands by name

Popular brands

Load more brands