manualshive.com logo in svg

VersaLogic VL-EPU-3311, Hardware Reference Manual

Share
Download
VersaLogic VL-EPU-3311 Hardware Reference Manual Download Page 3

VL-EPU-3311 Reference Manual 

iii 

Product Revision Notes 

Revision 1.10 

Updated CBR-4005 image (Figure 26) 

Revision 1.09 

Added GPIO voltage information on page 37 (The second bullet) 

Revision 1.08 

Updated BIOS Setup section. 

Revision 1.06 

Updated ground notice (page iv) 

Revision 1.05 

Updated the cable kit name on page 65 

Revision 1.04 

Added the part number and mating connector information for the I/O paddleboard on 
page 53 

Revision 1.03 

Updated Web links 

Revision 1.02 

Updated Figure 4 

Revision 1.01 

Added

 

Mini DisplayPort cable options 

Revision 1.00 

First release 

 

Support Page 

The 

Osprey Product Page

 contains additional information and resources for this product 

including: 

 

Operating system information and software drivers 

 

Data sheets and manufacturers’ links for chips used in this product 

 

BIOS information and upgrades 
 

Customer Support 

If you are unable to solve a problem after reading this manual, visiting the product support page, 
or searching the KnowledgeBase, contact VersaLogic Technical Support at (503) 747-2261.  
VersaLogic support engineers are also available via e-mail at [email protected]. 

Repair Service 

If your product requires service, you must obtain a Returned Material Authorization (RMA) 
number by calling 503-747-2261.  Be ready to provide the following information: 

 

Your name, the name of your company, your phone number, and e-mail address 

 

The name of a technician or engineer that can be contacted if any questions arise 

 

The quantity of items being returned 

 

The model and serial number (barcode) of each item 

 

A detailed description of the problem 

 

Steps you have taken to resolve or recreate the problem 

 

The return shipping address 

Warranty Repair 

All parts and labor charges are covered, including return shipping 

charges for UPS Ground delivery to United States addresses. 

Summary of Contents for VL-EPU-3311





































































Reviews:

No comments

Brands by name

Popular brands

Load more brands