background image

11

11

1

Fig. 1.11

=

=

Dotted line showing the position 

of the range when installed

17” 

15/16

(455.5 mm)

Anti-tip stability

device

Adjustable

bracket with

threaded nut

correctly fitted

Anti-tip stability

device fixing

3. 

Fix the stability bracket in place. It can be 

fixed as follows:

• 

To  the  floor  OR  on  the  rear  wall  by  #4 

screws (supplied).

• 

To  the  floor AND  on  the  rear  wall  by  #8 

screws (supplied).

• 

There are 8 x wood screws and 8 x 

screws with plastic

 

sleeve  anchors  supplied  with  the 

range in two separate kits.

 

Use the proper screws according to 

the type of material on the floor and/

or wall.

• 

If using the the plastic sleeve anchors: drill 

5/16” (8mm) diameter holes and insert the 

supplied plastic sleeve anchors before 

attaching  the  stability  bracket  with  the 

screws.

4. 

Slide  the  range  into  place,  ensuring  the 

bolt on the adjustable bracket slots under 

the stability bracket.

• 

Adjust the length of the bolt as necessary. 

Ensure  the  two  nuts  are  well  tightened 

after any adjustments.

IMPORTANT!

• 

Use  the  proper  screws  to  fix  the 

stability bracket in place according to 

the type of material on the floor and/or 

wall.

• 

Before  drilling  and  holes  or  inserting 

any screws into the floor or wall check 

that you will not damage any wiring or 

pipes.

WARNING 

- Slide range back so bolt head, on the adjustable bracket assembly, is 

--

under anti-tip bracket.

 

- Look for the anti-tip bracket securely attached to floor or wall.

 

- See installation instructions for details.

 

- Look for the adjustable bracket assembly securely attached to 

--

the back of the range.

 

- Slide range forward.

To verify the anti-tip bracket is installed and engaged:

Tip-Over Hazard

  

Anti-tip bracket

Adjustable bracket 

assembly to be fixed to 

the back of  the range

 

A child or adult can tip the range and be killed.

Install anti-tip device to range and/or structure per installation 

instructions.

Engage the range to the anti-tip device Installed to the structure.

Re-engage anti-tip device if range is moved.

Failure to follow these instructions can result in death or serious 

burns to children and adults

.

Summary of Contents for VDFSIE365 Series

















Reviews: