background image

20306746

33

WDV See-thru Gas Fireplace

SIGNATURE COMMAND SYSTEM OPERATION INSTRUCTIONS

SYSTEM CONFIGURATION/SETUP

All System configuration/setup is done on the Command 

Center.

NOTE:

 When using On/Off wall switch, the switch must be 

in the ON position to perform all configuration set ups at 

the command center.

COLD CLIMATE OPTION

Choose the Mode That Best Suits Your Needs
The Signature Command System is designed to operate 

in either Standing Pilot or Intermittent Pilot mode.

  The Standing Pilot Mode is best for colder climates 

when the pilot must remain on continuously to prevent 

condensation and ensure reliable operation.

  The Intermittent Pilot Mode is ideal for maximum effi

-

ciency, igniting the pilot only when needed to start your 

fireplace, lowering fuel consumption and reducing your 

carbon footprint.

Either mode benefits from the instantaneous battery back-

up, so you never have to worry about a power outage.

NOTE:

 The Signature Command System comes stan-

dard in the Intermittent Pilot mode, so you must follow 

the instructions below to switch to Standing Pilot Mode if 

needed.

Intermittent/Standing  Pilot  Setup  (Default  intermit

-

tent)

1.  Holding the ON button on the Command Center while 

turning on the master switch will toggle between stand-

ing pilot and intermittent pilot. 

2.  After the above operation, one beep (for standing pi-

lot) or two beeps (for intermittent pilot) will be given as 

confirmation.

Six-hour Safety Shutdown Option (Default ON)

1.  The system comes preset from the factory with a six 

(6) hour shutdown from its last command of operation. 

This is done to prevent the fireplace from continuing to 

operate if unattended. You may disable this feature if 

you wish.

 

Function 

Operation 

Default Setting

 

Intermittent/Standing 

Hold the ON

 s 

button while turning on the master switch 

Intermittent

  Pilot Setup 

(Beep once for standing pilot, twice for intermittent pilot) 

Pilot

  Standing Pilot Temp. 

Hold the ON

 s 

button 3 seconds (when the master switch

  Shutoff 

on the main burner is off)

  RF Remote Receiver 

Push the RF receiver On/Off button on the control board 

RF OFF   

  On/Off 

Beep once for ON and beep twice for OFF

  Learn Remote 

Hold the OFF

 t 

button while turning on the master switch

  Transmitter 

(Beep twice then press any handheld remote button)

  6-hour safety  

Press the ON

 s 

button and OFF

 t 

button simultaneously 

ON

  shutdown setup 

(Beep once for ON, twice for OFF)

NOTE:

 By disabling this feature, your fireplace may con

-

tinue to operate unattended.

2. When the master switch is in the ON position (“-"), 

pressing the ON button and the OFF button on the 

Command Center simultaneously will toggle between 

enabling and disabling the six-hour shutdown option. 

3.  After the above operation, one beep (for enabling the 

six-hour shutdown option) or two beeps (for disabling 

the six-hour shutdown option) will be given as confirma

-

tion.

Remote Transmitter Learn Function (Default OFF)

1.  The RF receiver button located on the Control Board 

must be in the on position before the learn function can 

begin. Use paper clip to depress button. One beep for 

RF receiver ON or two beeps for RF receiver OFF will 

be given as confirmation. Refer to Figure 42 for location.

2.  After the RF receiver is on, holding the OFF button on 

the Command Center while turning on the master switch 

will activate the learn function for the transmitter. 

3.  After the above operation, two beeps will be given and 

the green LED on the Command Center will flash for 

10 seconds. 

4. During the 10 seconds, press the OFF button on a 

transmitter to learn. Another two beeps will be given 

to confirm a successful learning. Refer to transmitter 

instructions for remote operations.

Shutting Off the Standing Pilot (Temporary Shut Off)

To shut off the standing pilot for service or summer shut 

down, press and hold the ON button on the Command 

Center for 3 seconds when the master switch is in the ON 

position (“-") and the main burner is off.

Note

: Pilot will resume the next time system is turned 

on.

Key Combinations for System Settings

NOTE: 

When On/Off wall switch is used, it must be in the 

On position to perform all system setups.

Summary of Contents for WDVST500NTSCSB





















































Reviews: