background image

VSW20 Wood Stove

14

20300059

INSTAllATION

3.  If the overall R-value of the system is greater than the 

R-value of the specified floor protector, the alternate is 
acceptable.

EXAMplE:

 The specified floor protector should be 3/4-inch 

thick material with k-factor of 0.84. The proposed alternate 
is 4” brick with an r-factor of 0.2 over 1/8” mineral board 
with a k-factor of 0.29
Step a: Use formula above to convert specification to R-

value:

Step b: Calculate R of proposed system. 
  4” brick of r = 0.2, therefore:
   R

brick

 = 0.2 x 4 = 0.8

  1/8” mineral board of k = 0.29, therefore
   R

mineralboard

 =         x 0.125 = 0.431 

   R

total

 = R

brick

 + R

mineralboard

 = 0.8 + 0.431 = 1.231

Step c: Compare proposed system Rtotal of 1.231 to 

specified R of 1.19. Since proposed system Rtotal is 
greater than required, the system is acceptable.

Definitions

FlOOR  pROTECTION  FOR  FIREplACE  IN-
STAllATIONS 

Do not assume your fireplace hearth is completely non-
combustible.  
Many fireplace hearths do not satisfy the “completely non-
combustible” requirement because the brick or concrete in 
front of the fireplace opening is supported by heavy wood 
framing as in 

Figure 11

. Because heat passes through brick 

or concrete readily, it can easily  pass through to the wood. 
As a result, such fireplace hearths can be a fire hazard and 
are considered a combustible floor.  
Keep in mind that many raised hearths will extend less than 
the required clearance from the front of the heater when 
it is installed. In such cases, sufficient floor protection as 
described above must be added in front of the hearth to 
satisfy the minimum floor protector requirement from the 
front of the stove: 18” (460 mm) from the front in Canada. 
Fireplace hearths must also offer the required protection 
of 8” (203 mm) on either side. 
Optional 3” (76 mm) short legs may be used only on  such 
hearths that meet the width and depth requirements out-
lined previously under “floor protection.”
Hearth rugs do not satisfy the requirements for floor pro-
tection.  

Fireplace installations also have special clearance require-
ments to the side walls, side decorative trim, and fireplace 
mantle. Refer to the information on  fireplace and mantel 
trim shields in this section.

ST1098
floor install

Wood framing 
requires protection 
from radiant heat

ST1098

Figure 11 - 
Supporting timbers under fireplace hearth 
are considered to be combustible

kEEp ThE STOVE ANd CONNECTOR A 
SAFE dISTANCE FROM SuRROuNdINg MA-
TERIAlS

Both a stove and its chimney connector radiate heat in all 
directions  when  operating,  and  dangerous  overheating 
of nearby combustible materials can occur if they are too 
close to the heat.  A safe installation requires that adequate 
clearance  be maintained between the hot stove and its 
connector and nearby combustibles.
Clearance  is  the  distance  between  either  your  stove 
(measured from the back edge of the stove’s top plate) or 
chimney connector, and nearby walls, floors, the ceiling, 
and any other fixed combustible surface.  Your stove has 
special clearance requirements that have been established 
after careful research and testing to UL and ULC standards.  
These clearance requirements must be strictly observed.
In addition, furnishings and other combustible  materials 
must be kept away from the stove as well.  In general, a 
distance of 48” (1220 mm) must be maintained between 
the stove and moveable combustible items such as dry-
ing clothes, furniture, newspapers, firewood, etc. Keeping 
those clearance areas empty assures that nearby surfaces 
and objects will not overheat.

 

r =                   = 

(ft

2

)(hr)(°F)

(Btu)(in)

1

k

(Btu)(ft)

(ft

2

)(hr)(°F)

 

K =                

 

k =                   = K x 12

(Btu)(in)

(ft

2

)(hr)(°F)

 

R = 

(ft

2

)(hr)(°F)

Btu

Summary of Contents for VSW20

























Reviews: