background image

51D0528

31

LX Series Direct Vent Gas Fireplace

AIR ReStRIctoR ADjuStMeNt

FP2719
Lx air restrictor

Bend Tabs Up 

for All Vertical 

Applications 

Only

Air Restrictor

Slide Left 

and Right

FP2719

Screw

The  fireplace  is  equipped  with  a  restrictor  plate  that  is 

located inside the top chamber of the fireplace. Depending 

upon the vent configuration, you may be required to adjust 

the restrictor position
1.  Remove glass frame.  

Refer to Glass Frame Removal, 

Page 27.

2.  Using  a  Phillips  screw  driver,  loosen  the  screw  that 

secures the air restrictor.  Do not back the screw all the 

way out.

3.  Slide the baffle on top of the restrictor plate such that it 

blocks a percentage of the grill opening.  Refer to the 

chart for recommended settings.

Note: All the settings above are based on the testing 

at the factory and provided as a guide for startup. on 

certain applications, adding a restrictor disc will help 

to achieve flame aesthetics.   

 

Venting height (feet) 

% of Grill opening

 

8 to 20 

100% (Factory Setting)

 

20 to 30 

50%

 

30 to 40 

0%

Figure 47 - 

Adjust Baffle on Air Restrictor 

Plate

Summary of Contents for Lexington LX32DV

















































Reviews: