Vermont Castings Lexington LX32DV Installation And Operating Instructions Manual Download Page 22

Page: 22 / 48

51D0528

LX Series Direct Vent Gas Fireplace

FIRepLAce INStALLAtIoN

checK GAS type

Use proper gas type for the fireplace you are installing. If you have conflicting gas type, do not install

fireplace. See dealer where you purchased the fireplace for proper fireplace according to your gas

type.

INStALLING GAS pIpING to FIRepLAce LocAtIoN

When using copper or flex connectors use only fittings

approved for gas connections. The gas control inlet is

3/8" NPT.

ARNING

A qualified installer or service person must

connect appliance to gas supply. Follow

all local codes.

For propane/Lp units, never connect

fireplace directly to the propane/Lp supply.

this burner system requires an external

regulator (not supplied). Install the external

regulator between the burner system and

propane/Lp supply.

INStALLAtIoN IteMS NeeDeD

Before installing fireplace and burner system, make sure you have the items listed below.

•

External regulator

•

Piping (check local codes)

•

Sealant (resistant to propane/LP gas)

(supplied by installer)

•

Test gauge connection*

• Sediment trap (recommended)

•

Equipment shutoff valve*

•

Tee joint

•

Pipe wrench

•

approved flexible gas line with gas connector (if allowed by local codes — not provided)

* A CSA design-certified equipment shutoff valve with 1/8" NPT tap is an acceptable alternative to test gauge

connection. Purchase the CSA design-certified equipment shutoff valve from your dealer.

For propane/LP connections only, the installer must supply an external regulator. The external regulator will reduce

incoming gas pressure. You must reduce incoming gas pressure to between 11 and 13 inches of water. If you do not

reduce incoming gas pressure, burner system regulator damage could occur. Install external regulator with the vent

pointing down as shown in

Figure 33.

Pointing the vent down protects it from freezing rain or sleet.

use only new black iron or steel pipe.

Internally tinned copper or copper tubing

can be used per National Fuel code, Section

2.6.3, providing gas meets hydrogen sulfide

limits, and where permitted by local codes.

Gas piping system must be sized to provide

minimum inlet pressure (listed on data plate)

at the maximum flow rate (Btu/hr). undue

pressure loss will occur if the pipe is too

small.

FP1977
external regulator

External

Regulator

100 gal. (min)

Propane/LP

Supply Tank

Vent Pointing

Down

Figure 33 -

External Regulator with Vent Pointing Down

(Propane/LP Only)

FP1977

external regulators may be necessary for

natural gas. one- or two-pound systems

will damage this appliance and may cause

fire hazard.

ARNING

Summary of Contents for Lexington LX32DV

















































Search results

Summary of Contents for Lexington LX32DV

Reviews:

Related manuals for Lexington LX32DV

Brands by name

Popular brands

Vermont Castings Lexington LX32DV, Installation And Operating Instructions Manual

Search results

Summary of Contents for Lexington LX32DV

Reviews:

Related manuals for Lexington LX32DV

Brands by name

Popular brands