20304852
ICFDV40 Fireplace Insert
33
TOUCH SCREEN REMOTE CONTROL OPERATION
4. After the signal is sent, the On/up and Off/down but-
tons become
fl
ame height controller again.
5. When the light button is
fl
ashing, slide up and down on
the arrow buttons will turn the light brightness
to HIGH or Off directly without pressing the
light button again to con
fi
rm
AUX Control (Optional)
The AUX control function is used to turn on or
turn off the auxiliary component connected to the
AC module of the Signature Command System.
Press the AUX button to turn on or turn off the
auxiliary.
1. When the auxiliary is turned on, the icon will become
solid text and the “ON” icon will appear below the
“AUX” icon.
2. When the auxiliary is turned off, the icon will become
hollow text and the “ON” icon will disappear.
NOTE:
Some
fi
replaces use the AUX function to control
options within the
fi
replace. Refer to
fi
replace manual for
operation.
Setting up Blank
Screen or Con-
stant Display in
Idle
Figure 49
There is an option to
set up how the LCD
displays and func-
tions when the trans-
mitter is in idle. There
are two choices:
1. A) Mode. When
the transmitter is in idle, the icons in the “touch area”
(timer, thermostat, blower, light and AUX) will disap-
pear, as shown in the
fi
gure on the left. When any of
the touch buttons is pressed, those icons will appear
and are ready to operate (default).
2. B) Mode. The transmitter always displays all available
icons showing current status of timer, thermostat,
blower, light and AUX as shown in the
fi
gure on the
right.
Press TIMER and THERMO buttons at the same time for
3 seconds to toggle between A) and B).
1. When the current setting is A), touch any place in the
touch area to bring up the icons then press TIMER but-
ton and THERMO button at the same time for 3 sec-
onds. The backlight will
fl
ash once to indicate that the
setting has changed to B).
2. When the current setting is B), pressing TIMER button
and THERMO button at the same time for 3 seconds
will switch to A) Mode. The touch area icons will disap-
pear.
Figure 49
Safety Features
1. Low Battery Detection
When low battery condition occurs, the transmitter will
turn off the
fi
replace.
A) Battery voltage is checked every one min-
ute. When the battery voltage is low, the
LCD displays a low battery icon which will
exist in all modes.
B) The transmitter will not operate with low
battery voltage. Change the batteries before the
batteries become too weak for normal operations.
2. Power On Initialization
After the power-on initialization, the transmitter sends
a signal to turn off the
fi
replace.
3. Thermal Shutdown
When the ambient temperature is more than 99°F, the
transmitter will turn off the
fi
replace.
A) The LCD will display “HI”.
B) The Transmitter will not function until
the room temperature has dropped be-
low 99 degree Fahrenheit.
4. Low Temperature Condition
When the ambient temperature is less than 40 degrees
Fahrenheit, the LCD will display “LO”, and NO SIGNAL
will be sent to turn on the appliance.
All functions still remain the same for
both Manual Mode and Thermostat
Mode
5. Child-proof Protection
The child-proof icon will be shown when
the child-proof mode is activated by
pressing the ON button and the OFF
button at the same time for three sec-
onds.
A) Enter childproof mode by pressing
and holding both the ON button and the OFF button
simultaneously for 3 seconds. The Childproof indi-
cator will be shown on the LCD.
B) Deactivate childproof mode by pressing and hold-
ing the ON button and the OFF button simultane-
ously for 3 seconds again. The Childproof indicator
disappears on the LCD.
C) The transmitter cannot be operated in childproof
mode.
