background image

5832
36CFDV cover

 

CFDV Series Direct Vent Gas Fireplace

Installation and Operating Instructions

Models: 33CFDV(N/P)(V/I)SL, 36CFDV(N/P)(V/I)SL, 42CFDV(N/P)(V/I)SL

20306739  1115  Rev. 2

INSTALLER: Leave this manual with the appliance.

CONSUMER: Retain this manual for  

future reference.

•  Do not store or use gasoline or other 

flammable vapors and liquids in the 

vicinity of this or any other appliance.

•  WHAT TO DO IF YOU SMELL GAS

  – Do not try to light any appliance.

  – Do not touch any electrical switch; do 

not use any phone in your building.

  – Leave the building immediately.

  – Immediately call your gas supplier from 

a neighbor's phone. Follow the gas 

supplier's instructions.

  – If you cannot reach your gas supplier, 

call the fire department.

•  Installation and service must be performed 

by a qualified installer, service agency or 

the gas supplier.

WARNING:  Improper  installation,  adjustment, 

alteration, service or maintenance can cause 

injury or property damage. Refer to this manual. 

For assistance or additional information consult 

a  qualified  installer,  service  agency  or  the 

gas supplier.   

This appliance may be installed in an aftermarket,* 

permanently located, manufactured home (USA 

only) or mobile home, where not prohibited by 

local codes.

This appliance is for use only with the type of gas 

indicated on the rating plate. This appliance is 

not convertible for use with other gases, unless 

a certified kit is used. 

*  Aftermarket: Completion of sale, not for purpose of resale, from 

the manufacturer. 

 WARNING: 

FIRE OR EXPLOSION HAZARD

Failure to follow safety warnings exactly 

could result in serious injury, death or 

property damage.

DANGER

HOT GLASS 

WILL

CAUSE BURNS

.

DO NOT TOUCH GLASS

UNTIL COOLED.

NEVER ALLOW CHILDREN

TO TOUCH GLASS.

Un panneau vitré chaud

 peut 

causer des brûlures.

Laissez refroidir le panneau

vitr

é

 avant d’y toucher.

Ne laisser jamais

 les enfants

toucher le panneau vitr

é

.

A barrier designed to reduce the risk of burns from 

the hot viewing glass is provided with this 

appliance and shall be installed.

Une barrière visant à réduire le risque de brûlure 

par le hublot chaude est fournie avec cet 

appareil et doit être installé.

DANGER

CERTIFIED

S

AFETY

 

B

ARRIER

Summary of Contents for 33CFDVNI





































































Reviews: