background image

User Guide quadroPOL

2

Unpacking

To ensure top quality, we carefully checked the quadroPOL module before packaging. Nevertheless, we cannot 
fully exclude damage during transportation. Therefore, we kindly ask you to inspect quadroPOL by yourself, 
once you receive the module. In case there is anything unusual about the unit or its packaging, do not hesitate to 
contact your dealer or us, to solve the problem.

You should find the following items in the box:

 

-

the quadroPOL module

 

-

one ribbon-cable (10-pole to 16-pole)

 

-

four  M-type screws 3 x 6 mm with matching plastic washers

 

-

this operating manual 

Setup

quadroPOL was designed to be mounted and used in Eurorack modular systems. Its power supply, connectors and 
dimensions match the typical specifications (VERMONA Modular Case, Doepfer A-100 and compatible systems). 
Mounting equals any other Eurorack module:

1. 

Switch off the power supply! For safety reasons, also remove the detachable power cord from your frame 
before mounting the module!

2.  Connect the supplied ribbon-cable with its 10-pole connector to the corresponding multi-pin connector on 

quadroPOL’s rear.

Summary of Contents for quadroPOL














Reviews: