Z207251-0C
Page 2 of 42
©2020 Veris Industries USA 800.354.8556 or +1.503.598.4564 / [email protected] 0420
Alta Labs, Enercept, Enspector, Hawkeye, Trustat, Aerospond, Veris, and the Veris ‘V’ logo are trademarks or registered trademarks of Veris Industries, L.L.C. in the USA and/or other countries.
Other companies’ trademarks are hereby acknowledged to belong to their respective owners.
E34 Series Installation Guide
TM
Safety Information
Control system design must consider the potential failure modes of control paths and, for certain critical control functions, provide a means to acheive a safe state
during and after a path failure. Examples of critical control functions are emergency stop and over-travel stop.
For additional information about anticipated transmission delays or failures of the link, refer to NEMA ICS 1.1 (latest edition).
Safety Guidelines for the
Application, Installation, and Maintenance of Solid-State Controls
or its equivalent in your specific country, language, and/or location.
LOSS OF CONTROL
• Ensure that the system will reach a safe state during and after a control path failure.
• Separate or redundant control paths must be provided for critical control functions.
• Test the effect of transmission delays or failures of communication links.
• Each implementation of equipment using communication links must be individually and thoroughly tested for proper operation before placing
it in service.
Failure to follow these instructions can result in death or serious injury.
WARNING
Provide a disconnect device to disconnect the meter from the supply source. Place this device in close proximity to the equipment and within easy reach of the
operator, and mark it as the disconnecting device. The disconnecting device shall meet the relevant requirements of IEC 60947-1 and IEC 60947-3 and shall be
suitable for the application. In the US and Canada, disconnecting fuse holders can be used. Provide overcurrent protection and disconnecting device for supply
conductors with approved current limiting devices suitable for protecting the wiring.
FCC PART 15 INFORMATION
E34A Models: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits
are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there
is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following
measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
– Connect the equipment to an outlet on a circuit different from that of the receiver.
– Consult the dealer or an experienced radio/TV technician for help.
The user is cautioned that any changes or modifications not expressly approved by Veris Industries could void the user’s authority to operate the equipment.
E34E Models: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment
generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be
required to correct the interference at his own expense.
CAN ICES-3 (B) /NMB-3(B)
If this product is used in a manner not specified by the manufacturer, the protection provided by the product may be impaired.
The installer is responsible for conformance to all applicable codes.
The safety of any system incorporating this equipment is the responsibility of the assembler of the system.
Note: See IEC 60950-1:2005, Annex W for more information on communications and I/O wiring connected to multiple devices.
Protective bonding: electrical connection of accessible conductive parts or protective screening to provide electrical continuity to the means
for connection of an external protective conductor.
HAZARD OF ELECTRIC SHOCK, EXPLOSION, OR ARC FLASH
• This product must be installed inside a suitable fire and electrical enclosure.
• Follow safe electrical work practices. See NFPA 70E in the USA, or applicable local codes.
• This equipment must only be installed and serviced by qualified electrical personnel.
• Do not use this device for critical control or protection applications where human or equipment safety relies on the operation of the control
circuit.
• Do not install this product in hazardous or classified locations.
• Read, understand and follow the instructions before installing this product.
• Turn off all power supplying equipment before working on or inside the equipment.
• Product may use multiple voltage/power sources. Disconnect all sources before servicing.
• Use a properly rated voltage sensing device to confirm that power is off.
• Do not use data from this device to confirm power is off.
• Replace all doors, covers and protective devices before powering the equipment.
• Do not exceed the product's ratings or maximum limits.
• Treat communications and I/O wiring connected to multiple devices as hazardous live until determined otherwise.
Failure to follow these instructions will result in death or serious injury.
DANGER
