background image

WARNING:  TO  PRE VENT  FIRE  OR  ELEC TRICAL 
SHOCK HAZARD, DO NOT EXPOSE THIS PRODUCT 
TO RAIN OR MOISTURE.
CAUTION:  USE  OF  CONTROLS  OR  ADJUSTMENTS 
OR PERFORMANCE OF PROCEDURES OTHER THAN 
THOSE SPECIFIED MAY RESULT IN HAZARDOUS 
RADIATION EXPOSURE.
CAUTION: DANGER OF EXPLOSION IF BATTERY IS 
INCORRECTLY REPLACED. REPLACE ONLY WITH 
THE SAME OR EQUIVALENT TYPE.
WARNING: MAINS PLUG IS USED AS DISCONNECT 
D E V I C E  A N D  I T  S H O U L D  R E M A I N  R E A D I LY 
OPERABLE DURING INTENDED USE. IN ORDER 
TO DISCONNECT THE MAINS PLUG FROM MAINS 
COM PLE T ELY, T H E M AI NS PLU G SH O U LD B E 
D I S CO N N E C T E D  FR O M  T H E  M A I N S  S O C K E T 
OUTLET COMPLETELY.

Caution:

This product utilizes a laser. Use of controls or 
adjustments or performance of procedures other 
than those specified may result in hazardous 
radiation exposure. Do not open covers and do 
not repair yourself. Refer servicing to qualified 
personnel.

This product contains a low power laser device.

TH E LIG HTN I NG FL A SH AN D AR ROWH E AD WITH I N 
THE TRIANGLE IS A WARNING SIGN ALERTING YOU OF 
"DANGEROUS VOLTAGE" INSIDE THE PRODUCT.

SEE MARKING ON BOTTOM / BACK OF PRODUCT

T H E  E XC L A M AT I O N  P O I N T  W I T H I N  T H E  T R I A N G L E 
IS A WARNING SIGN ALERTING YOU OF IMPORTANT 
INSTRUCTIONS ACCOMPANYING THE PRODUCT.

CAUTION:  TO  REDUCE  THE  RISK  OF  ELECTRIC  SHOCK,  DO 
NOT REMOVE COVER (OR BACK). NO USERSERVICEABLE 
PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE 
PERSONNEL.

FCC information

This device complies with part 15 of the FCC 
Rules. Operation is subject to the following two 
conditions: (1) This device may not cause harmful 
interference, and (2) this device must accept any 
interference received, including interference that 
may cause undesired operation.
This equipment has been tested and found to 
comply with the limits for a Class B digital device, 
pursuant to part 15 of the FCC Rules. These limits 
are designed to provide reasonable protection 
against harmful inter ference in a residential 
installation. This equipment generates, uses 
and can radiate radio frequency energy and, if 
not installed and used in accordance with the 
instructions, may cause harmful interference 
to radio communications. However, there is no 
guarantee that interference will not occur in a 
particular installation. If this equipment does 
cause harmful interference to radio or television 
reception, which can be determined by turning 
the equipment off and on, the user is encouraged 
to try to correct the interference by one or more of 
the following measures: 
–   Reorient or relocate the receiving antenna. 
–   I n c r e a s e  t h e  s e p a r a t i o n  b e t w e e n  t h e 

equipment and receiver. 

–  Connect the equipment into an outlet on a 

circuit diff erent from that to which the receiver 
is connected. 

–   Consult the dealer or an experienced radio/TV 

technician for help.

WARNING: Changes or modifications to this unit 
not expressly approved by the party responsible 
for compliance could void the user's authority to 
operate the equipment.

This Class B digital apparatus complies 
with Canadian ICES-003.

Safety Precautions

- 1 -

Summary of Contents for CD2965SB














Reviews: