Ventura DAI7T02B, Instruction Manual / Installation Manual

Page: 16 / 18

selected by keeping the slider (3) key pressed down. The setting
begins at level 1 and increases by 1 level every 0.4 seconds. When
setting “9” is reached, the setting will not be changed further.
If the setting level has been selected using slider key (3), the
start level is “9“ (maximum level). Keep the button pressed down to
lower the active level by 1 every 0.4 seconds. When setting “0” is
reached, there will be no further setting changed. The setting can
only be changed by pressing slider key (3) again.
(4). The display (5) of the zone selected lights up, while the remaining
displays are dimmed. Press the Cooking zone (4) and MINUS (2)
buttons at the same time and the setting level of the zone is changed
to 0. Alternatively, the MINUS button (2) can be used to reduce the
setting level to 0.
If a cooking zone is “hot”, “H” and “0” will be alternately displayed.
Switching-OFF all cooking zones
Immediate switching-OFF of all cooking zones can be achieved
anytime by means of the ON/OFF key. In the standby-mode an “H“
appears on all cooking zones which are “hot“. All other cooking zone
displays are not illuminated.
Wattage settings
The output of the cooking zones can be set in 9 steps which are
displays.
In the cooking zone located on the front left, when selecting
the power level 9 and after 30 minutes operating, the power will
decrease slightly for safety reasons. In case more power is required,
select the boost level (“P”)
Flexible Area
There are several possible cooking zone combinations:
Boost function
The power management is based on on the principle that the last
entry is requested by the induction as top priority. That means that
previous actions and settings also made for the other cooking zones
are reversed automatically, if necessary.
-
providing a correction period of 3 sec before the power is reduced
automatically to a minimum cooking stage.
- If the setting is adjusted within the correction period, the power
management checks the settings again. Should a new setting lead to
further power reduction, the correction period starts again.
- If no automatic correction needs being made to the cooking zone
remains as a steady display indication. Should the situation change
again on the power reduced cooking zone, no automatic power
NOTE:
When selecting the Booster function on any of the rear areas (left
or right), the front area located on the same side will automatically
power on the rear area. This allows you to benefit from an extra
powerful Booster.
However, when selecting the Booster function on any of the front
areas (left or right), the rear area located on the same side may be
operated up to power level 8, as it will not require as much energy
input.
Residual heat indicator
It is meant to indicate to the user that the glass ceramic has a
dangerous touch temperature in the circumference of a cooking
zone. The temperature will be determined following a mathematical
model and the remaining residual heat will be indicated by means of
“H” on the corresponding 7-segment display.
Heating-up and cooling down will be calculated dependent on:
· the selected setting („0“ to „9“)
· the ON/OFF time.
After switching-OFF the cooking zone the respective display shows
“H” until the assigned cooking zone temperature is mathematically
in a uncritical level. ( 60°C).
For each activated cooking zone a max. operating time is defined. The
max. operating time is depending on the selected cooking stage. After the
expiration of the max. operating time the cooking zone is automatically
Each actuation of the cooking zone status (changing the cooking level
etc.) resets the count-down timer to the initial starting value.
Timer settings takes priority vs. operating time limitations for high cooking
stage setting.
Protection against unintended switching-ON
· If the electronic control realizes a continuous operation of keys
for approx. 10 seconds, it switches OFF automatically. The control
sends out an audible failure signal for 10 seconds, so that the user
can remove the object which has been mistakenly placed onto the
operation surface. The displays show the failure code “ E R 0 3 “ .
If the failure carries on for more than 10 seconds, only the code “E
R 0 3 “ will be displayed as long as the failure will be recognized
by the electronic control. If the cooking zone is in the “hot” status,
“H“ will appear on the display in alteration with the failure notice.
· If no cooking zone will be activated within 20 seconds after
switching-ON by means of the Power-key, the control switches
15
Actived the boost function; select the heating zone by touching the zone
select key (4); touching the boost control key (9), the zone indicator
show “P.” and the power reach Max.
Cancel the Boost function; touching the relevant zone select key (4)
that you wish to cancel. 1a.Touching the slider key (3) to cancel the
Boost function, then the cooking zone will revert to level 9.
1b.Touching “-” and “+” control together at the same time, the cooking
zone switch off and the boost function cancel automatically.
The boost function can work in any cooking zone. The cooking zone
returns to level 9 after 5 minutes.
1. To activate flexible area as a single big zone, press the zone selected
key (4) and at the same time for the left group or press the zone
selected key (4) at the same and time for the right group.
2. The flexible zone indicator next to the power level indicator
will be light up.
3. According to the heating zone where the pan is placed, adjust heat
setting by touching the front left zone “+”or “-” regulating (3)
control key.
4. If the pot is moved from the front to rear part (or viceversa),
the flexible area detects automatically the new position, keeping the
same power.
Flexible area is made of two independent inductors that can be
controlled separaately. When working as a single zone,
a cookware is moved from one zone to the other one within the flexible
area keeping the same power level of the zone where the cookware
originally was placed, and the part that is not covered by cookware is
automatically switched off.
Activating hood;
You can activate the hood by pressing the hood key (10) then adjust
the hood power level by pressing slider (3) key.
Deactivating hood;
You can activate the hood by pressing the hood key(10) then
adjust the hood power level ‘’0’’ by pressing slider (3) key.