background image

4

VUT 100 P mini

UNIT OPERATION SAFETY PRECAUTIONS

Do not touch the unit controls with wet hands. 

Do not carry out the unit maintenance with 

wet hands. 

Do not wash the unit with water. Protect 

the unit electric parts from water ingress.

Use the unit only as intended by the 

manufacturer. Do not connect a clothes dryer 

or other similar equipment to the ventilation 

system. 

Do not put any water containers on the unit. 

i.e. flower vases. 

Do not sit on the unit and do not put any 

objects on it.

OFF

ON

Disconnect the unit from power supply prior 

to maintenance.

Do not let children operate the unit. 

Do not damage the power cable while 

operating the unit. Do not put any objects 

on the power cable.

Keep combustible gases and inflammable 

products away of the unit. 

Do not open the operating unit. 

In case of unusual sounds, smoke disconnect 

the unit from power supply and contact the 

service centre.

During long-term operation of the unit 

periodically check the mounting for 

reliability. 

Do not block the air duct when the unit is on. 

Do not let air flow from the unit be directed 

to the open flame devices or candles. 

Summary of Contents for VUT 100 P mini
















Reviews: