background image

 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

The

 

                     

      

Guarantee 

 

Applicable only to products installed and used in the United Kingdom.  For details of guarantee outside the United Kingdom contact your local 

supplier. 

 

Vent-Axia guarantees its products for two years from date of purchase against faulty material or workmanship.  In the event of any part being found 

to be defective, the product will be repaired, or at the Company’s option replaced, without charge, provided that the product:- 

 

 

Has been installed and used in accordance with the instructions given with each unit. 

 

Has not been connected to an unsuitable electricity supply. (The correct electricity supply voltage is shown on the product rating label 
attached to the unit). 

 

Has not been subjected to misuse, neglect or damage. 

 

Has not been modified or repaired by any person not authorised by the company. 

 

IF CLAIMING UNDER TERMS OF GUARANTEE 

Please return the complete product, carriage paid to your original supplier or nearest Vent-Axia Centre, by post or personal visit.  Please ensure 

that it is adequately packed and accompanied by a letter clearly marked “Guarantee Claim” stating the nature of the fault and providing evidence of 

date and source of purchase. 

 

The guarantee is offered to you as an extra benefit, and does not affect your legal rights 

 

Head Office: Fleming Way, Crawley, West Sussex, RH10 9YX. 
 

UK NATIONAL CALL CENTRE

, Newton Road, Crawley, West Sussex, RH10 9JA

 

SALES ENQUIRIES: 

  

Tel: 0344 8560590  

Fax: 01293 565169

  

TECHNICAL SUPPORT: 

Tel: 0344 8560594  

Fax: 01293 532814 

 

For details of the warranty and returns procedure please refer to 

www.vent-axia.com

 or write to Vent-Axia Ltd, Fleming Way, Crawley, RH10 9YX 

 
409188 D 

 

 

 

 

 

 

 

 

                                             1019 

Summary of Contents for Solo Pro HTP













Reviews: