manualshive.com logo in svg

Vent-Axia FAN7200, Installation Instructions Manual, Page: 7 / 7

Share
Download
Vent-Axia FAN7200 Installation Instructions Manual Download Page 7

MultiVent Continuous Extract Ventilation

Installation Instructions

     

Specifications are subject to change without notice. 

Distributed by Simx Limited

[email protected] | www.manrose.co.nz

Appraisal No.1152 [2021]

PUB1644 2112

SPARE PARTS

WARNING: THE FAN AND ANCILLARY CONTROL EQUIPMENT MUST BE ISOLATED FROM THE POWER SUPPLY 
DURING PART REPLACEMENT.

1.   Individual faulty parts should not be replaced due to complexity of assembly. Only the full scroll assembly is replaceable. 

2.   To remove the scroll assembly, isolate the power, then use a coin or similar to depress the cover retention clips and remove the cover. 

3.   Disconnect and remove the power supply and signal leads.

4.   Remove the scroll assembly by unscrewing the two screws and unclipping the clips in the opposite two corners and lift the scroll  
     assembly out of the housing.

5.   The fan has sealed for life bearings, which do not require lubrication. Expected service life is at least 45,000 hours continuous running.

6.   Upon reassembly, check all fixings are tight and secure.

Summary of Contents for FAN7200








Reviews:

No comments