Venstar T2700 Owner'S Manual Download Page 9

Page: 9 / 79

AUTO MODE

Pressing the UP or DOWN buttons in Auto mode
will adjust

both

the heat and cool set temperatures

simultaneously.

buttons.

Adjust the desired

set temperature with the

EAT

OOL

AUTO

HEAT OR COOL MODE

Pressing the UP or DOWN buttons in Heat

Cool mode will

adjust only the heat

cool set temperature.

buttons.

Adjust the desired

set temperature with the

OOL

Page 1.3

Selecting Your Desired Temperature

(adjusting the setpoints)

EAT

OOL

AUTO

FanOn

Using the Fan Button

Press

FAN

Fan On

indicates constant fan operation.

If Fan On is selected the fan will run
continuously at all times, except in Off,

and

will only run if there is a heating or

cooling demand in Unoccupied periods.
Pressing the FAN button toggles this
feature on or off.

Summary of Contents for T2700
















































































Search results

Summary of Contents for T2700

Reviews:

Related manuals for T2700

Brands by name

Popular brands

Venstar T2700, Owner'S Manual

Search results

Summary of Contents for T2700

Reviews:

Related manuals for T2700

Brands by name

Popular brands