background image

3

4

1.2

 DESCRIPTION

The product is a control unit to control electrical motors powered from the grid with power of max. 500 W

(230 V) or max. 250 W (110 V).

Ideal for activating motorised awnings, shutters and blinds with settable Up-Down-Stop, step and manual 

modes.

The ISM (industrial, scientific and medical) radio frequency band guarantees a long range, even through walls 

and ceilings. 

Simple programming with dip-switches, reduced dimensions with breakable tabs (pic. 1.1c) for fixing with

screws (pic. 1.2a) or for insertion into connection boxes up to 55 mm in diameter (pic. 1.2b, 1.2c and 1.2d).

1 PRODUCT FEATURES 

43mm

21mm

52mm

Led

Dip switches

Button 

58mm

1.1

 TECHNICAL DATA 

From the grid  120-240 Vac
1 motor powered from the grid: 
230V max 500W,
110V max 250W 
100
433.920MHz ISM
IP20
-20 +55 °C
52x43x21 mm

Power supply 
Outputs 

Num. of programmable transmitters 
Radio frequency 
Protection rating 
Operating temperature
Dimensions

Pic.1.1a

- Installation must be carried out only by qualified technicians in compliance with the electrical and safety 

standards in force. 

- All connections must be made with the power turned off. 

- Use suitable cables. 

- Do not cut through the aerial (see picture 1.1b) 

- A suitably sized disconnection device must be set up on the electric power line that supplies the product. 

- Disposal of waste materials must fully respect local standards. 

WARNINGS 

Pic.1.1b

Pic.1.1c

Pic.1.2a

Pic.1.2b

Pic.1.2c

Pic.1.2d

Pic.1.2e

L

N

M

Summary of Contents for VELA-RX

















Reviews: