background image

USER INSTRUCTIONS 

HELPFUL HINTS 

Abnormal Operation 
Any of the following are considered to be abnormal operation and may require servicing: 

Yellow tipping of the burner flame. 
Sooting up of cooking utensils. 
Burners not igniting properly. 
Burners failing to remain alight. 
Burners extinguished by cupboard doors. 
Gas valves, which are difficult to turn. 
In case the appliance fails to operate correctly, 

contact the authorised Service Department, 

CUCINA Appliances on 1800 444 357 
WARNING

: Servicing should be carried out only by authorised personnel.

Always use the correct diameter pan, one that is the same or slightly larger than the flame ring. 
The flame should never exceed the diameter of the pan. 
The bottom of the pan should be flat and wherever possible, keep the lid on the pan when 
cooking. 

Depending on the model the following burners are provided: 
Large (Rapid or Triple Crown) – for rapid cooking or boiling large quantities of liquid 
Wok – for rapid cooking or boiling large quantities of liquid 
Medium (Semi-rapid) – for general cooking 
Small (Auxiliary)– for slow or simmer cooking 
Fish Kettle – for specialised cooking 

All burners are variable between full and low positions 

WARNING 

Do not use commercial simmering aids as these can create excessive heat, which can damage the 
appliance. 

CLEANING THE APPLIANCE 

Alway

s

allow the appliance to cool down before cleaning to avoid a burn injury. 

Do not use caustic or abrasive agents, coarse wire wool or hard tools as these can damage the 
surface finishes. 

Normally, wiping with a soft cloth dampened with hot detergent solution is sufficient but for 
stubborn marks the following is recommended: 

Vitreous Enamel parts – use only a cleaner that is recommended for this type of material. 

Burner Assemblies – remove from the hob and soak for about 10 minutes in hot detergent 
solution. Rinse off and dry checking that the burner holes are not clogged, then reassemble in the 
correct order.

7

Summary of Contents for V3G1WC6

















Reviews: