background image

 

 

H O W  T O  R E A D  E A C H  DIS P L AY

1.As shown in FIG. R:

i.Upper  line  shows 

that  your  current 

r i d i n g   s p e e d   i s  

20.2km/h.

ii.KM  means  you  are 

in metric system and 

all  the  speed  and 

d i s t a n c e  w i l l  b e 

represented in metric.

iii.Lower line shows the clock. 

iv.Icon  "

"  or    "

"  flashing  shows  that  your 

current  speed  is  higher  or  lower  than  the 

average speed. 

v."      " flashing means the computer is receiving the

2.Press MODE and switch to the display as FIG.S:

i.Upper  line  shows  that  your  current  riding 

speed is 20.2km/h.

ii.Lower  line  shows  that  your  riding  distance 

is 5.6 Kilometres 

3.Press  MODE  again 

a n d  s w i t c h  t o  t h e 

display as FIG.T:

i.Upper  line  shows   

your  current  riding 

speed.

ii.Lower  line  shows 

your riding time.

iii.It  will  stop  counting 

automatically if there 

is  no  signal  received 

over 6 seconds.

4 . P r e s s  M O D E  a n d 

switch to the display as 

FIG.U.  The  upper  line 

shows  your  current 

speed,  and  the  lower  line  shows  your  current 

pulse rate. (VS-204A/VS-212A)

5.Press  MODE  again 

a n d  s w i t c h  t o  t h e 

display as FIG.V:

I. U p p e r  l i n e  s h o w s   

your  current  riding 

speed.

ii.Lower  line  shows  that 

the temperature where 

19

FIG.R

KM/H

SPD

18

FIG.S

FIG.T

FIG.U

KM/H

SPD

DST

KM/H

SPD

RTM

Note: Do not use the heart monitoring chest belt near a computer,

wireless router, mobile or any appliance emmitting an 

electromagnetic wireless signal. This will cause interference and

inaccurate measurements could occur.

signal correctly.

Summary of Contents for VS-204













Reviews: