background image

VELLEMAN                                                                                  CAMSET5A -- VERSION II 

3

7.  Damage Requiring Service - The unit should be serviced by qualified 

service personnel when : 
-  The power cord or the plug has been damaged. 
-  Objects have fallen or liquid has been spilled into the unit. 
-  The unit has been exposed to rain. 
-  The unit does not appear to operated normally or exhibits a marked 

change in performance. 

-  The unit has been dropped or the enclosure is damaged. 
 

8.  Replacement Parts - Use only manufacturer specified parts. 

Unauthorised substitutions may result in fire, electric shock of other 
hazards. 

 
9.  Service - The user should not attempt to service the unit beyond that 

described in the operating instructions. All other servicing should be 
referred to an authorised service personnel. 

 

Warning :

 The said Rear Observation Systems are to be used with, not 

instead of, other viewing aids in your vehicle such as front, rear, and side 
mirrors. Safe driving practices, alertness, and visual and physical fitness are 
prerequisites for your driving safety. The Manufacturer shall not be held liable 
for any accidents which may occur while operating this system. 
 

INTRODUCTION AND FEATURES 

 
This Hi-sharp Rear view system can lighter your worries on backing and 
parking your car or truck. See and hear what's behind you and drive with 
confidence. 
 
Monitor : 

  Dual camera input 

  High Resolution - 500 TV lines 

 Built-in 

speaker 

  Free voltage from DC 12V to 24V 

  Can be automatically activated when vehicle is shifted into reverse 

 
Camera : 

  With board lens for maximum viewing angle 

  High resolution with 380 TV lines 

  Water proofed case 

 Built-in 

microphone 

  Low light sensitivity - 0.1 lux 

Summary of Contents for CAMSET5A











Reviews: