background image

 

MINI PC SCOPE PCSU01 
 
User manual

 

F e a t u r e s  

 

test leads 

 

software download 

 

USB cable 

 

design enclosure 

S p e c i f i c a t i o n s

 

 

oscilloscope: 

o

 

bandwidth: DC to 200 kHz ± 3 dB 

o

 

input impedance: 100 kO / 20 pF 

o

 

maximum input voltage: 30 V (AC + DC) 

o

 

time base: 10 µs to 500 ms per division 

o

 

input range: 100 mV to 5 V/division 

o

 

input sensitivity: 3 mV display resolution 

o

 

readouts: true RMS, dBV, dBm, p to p, Duty cycle, Frequency… 

o

 

record length: 1k samples 

o

 

sampling frequency: 62.5 Hz to 1.5 MHz 

o

 

sample history function 

o

 

auto set-up function 

o

 

pre-trigger function: on 0.1 ms/div .. 500 ms/div ranges 

o

 

persistence options: colour graded, Variable and Infinite 

 

spectrum analyser: 

o

 

frequency range: 0 .. 150 Hz to 75 kHz 

o

 

operating principle: FFT (Fast Fourier Transform) 

o

 

FFT resolution: 512 lines 

 

transient recorder: 

o

 

timescale: 20 ms/div to 2000 s/div 

o

 

max. recording time: 9.4 h/screen 

o

 

automatic storage of data 

o

 

record and display of screens 

o

 

max. number of samples: 100/s 

o

 

min. number of samples: 1 sample/20 s 

 

general information: 

o

 

markers for: amplitude/voltage and frequency/time 

o

 

input coupling: DC and AC 

o

 

8 bit resolution 

o

 

storage of display and data 

o

 

dimensions: 85 x 40 x 14 mm 

 

minimum system requirements: 

o

 

Windows® XP, Vista, 7, 8, 10 

o

 

mouse (or mouse pad) 

o

 

free USB port 1.1 or 2.0 

Software installation

 

 
Download the latest software version from 

www.velleman.eu.

 

Type PCSU01 in the search box and check the download section. 
• Download the PCSU01_setup.zip file 
• Unzip the files in a folder on your drive 
• Double click the “setup.exe” file 
An install wizard will guide you through the complete installation 

Summary of Contents for 5410329646165











Reviews: