background image

1.2.4. chair Back

The chair back features an adjustable shoulder support. By loosen-
ing the two hand screws, it is possible to tilt the shoulder support 
forwards or backwards. To raise the chair back, loosen the two 
bolts on the telescopic tube which is visible when the shoulder 
support is folded back. The height of the chair back can now be 
adjusted and increased by up to 10 cm.

Depending on how the powerchair is equipped, it may have: fixed 
back tilt, manual back tilt or electric back tilt.

The fixed back tilt can be regulated (using tools) by adjusting the 
tilt pole behind the chair back. The pole can be released from the 
ball shaft at one end and either extended or shortened by turning 
the ends in the middle piece. The manual back tilt can be adjusted 
using the gas spring handle (push down) while pushing the chair 
back into the desired position. Release the handle to secure the 
chair back again.

The electric chair tilt can be operated from the tilt switch (normally 
located on the same side as the control box). 

1.2.5. neck sUpport

The height and position of the neck support (optional) are adjust-
able. By loosening both hand screws, the neck support can be 
positioned as desired.

note! 

If you need to raise the neck support, it is possible to raise 

the shoulder support, see above.

3.0. maintenance

3.0.1. Batteries

The VELA Blues 200 is equipped with two 34 Ah maintenance-
free and vapour-free batteries. Good-quality new batteries provide 
the equivalent of an operating range of 18 km. Experience shows 
that this covers the daily needs of most users. The batteries are 
dimensioned to be fully run down 220 times. Their lifetime will be 
extended significantly if they are only partially run down before 
charging. Defective batteries must be replaced with batteries of the 
same type. We recommend that batteries be replaced by a service 
technician.

note!

 When installing batteries, extreme care must be taken to 

c/- correctly. Red wire to the + pole. Incorrect connection 
can damage the powerchair’s electronics.

note!

 Batteries must not be disposed of with ordinary household 

rubbish. Used batteries and other electrical equipment must be 
deposited at an approved recycling centre according to the marking 
on the product.

3.1. charging

3.1.1. Battery indicator

The control box has a built-in battery indicator. For fully charged 
batteries, three groups of coloured LEDs light up. During use, the 
voltage in the batteries falls, and the row of lights decreases: The 
lights go off one at a time. 
•  Green signal = DRIVE
•  Yellow signal = Recharging needed soon 
•  Red signal = Recharging needed immediately 
The battery indicator will flash to call attention to low battery 
power.

8

17

Summary of Contents for Blues 200

























Reviews: