background image

1.0. User manUal

This powerchair is a class A (EN 12184) electric wheelchair. The first attempts to operate the chair 
should be made in an area with plenty of floor space. Choose a low operating speed (press the 
‘down button’ a few times) until you have become accustomed to the chair.

1.1. Before operation

Before starting the powerchair, you should check the following:
•  The footrest is in place and both feet are placed properly on the footplate.
•  The electric lift (seat lift) is in the lowest position.
•  The electric tilt (seat tilt) is in neutral position.
•  Both motors are connected (both disconnection arms are horizontal).
•  The powerchair is turned on by pressing the I/O button.

1.1.1. entering and exiting

Always turn off the power before entering or exiting the chair (the I/0 button).

1.1.2. footplate

The footplate can be folded up to allow you to place your feet on the floor.

Warning! 

Do not stand on the footplate or footrests – the chair can tip and you may loose your 

balance.

part

maintenance 
carried oUt By

maintenance

interval

WHEELS

User

Check that the tyres are not worn and that 
stones or other objects are not sitting in 
the tread. 
If the wheels are pneumatic, check the air 
pressure, which must be between 2.20-3.5 
Kilo Pascal. 
The wheel can be inflated with either a car 
pump or at a service station.

Once a 
month, 
depending 
on use

CHANGING 
WHEELS

VELA

Contact VELA

CONTROL BOx

User

The control box and the rubber seal 
around the joystick must always be kept 
clean. Once a week, you should check that 
the joystick returns to its original position 
and that the rubber seal has not been 
damaged. If this is not the case, contact 
VELA.

Once a 
week

TESTING 
CONTROL BOx 
FUNCTIONS

User

1. Check the on-off switch.
2. Check the horn.
3. Check the speed – try accelerating and 
decelerating.
4. Check the seat lift – raise and lower the 
seat to its full extent.
5. Check the seat tilt – tilt the seat all the 
way backwards and all the way forwards.
If any of the functions do not work or if 
anything feels different to normal, contact 
VELA. 

Once a 
month

BATTERIES

VELA

Batteries must be replaced by VELA.
If the batteries are leaking, avoid touching 
them as the contents are corrosive.

In the event 
of flat or 
defective 
batteries

ACCESSORIES

User

All accessories such as footrests, armrests 
and body supports must be adjusted using 
the tools supplied.

Once a 
month

20

5

Summary of Contents for Blues 200

























Reviews: