Vega VEGABAR 28 Operating Instructions Manual Download Page 41

Page: 41 / 56

13 Supplement

VEGABAR 28 • Three-wire 1 x transistor or 4 … 20 mA

57534-EN-220826

13 Supplement

13.1 Technical data

Note for approved instruments

The technical data in the respective safety instructions which are included in delivery are valid for

approved instruments (e.g. with Ex approval). These data can differ from the data listed herein, for

example regarding the process conditions or the voltage supply.
All approval documents can be downloaded from our homepage.

Materials and weights
Materials, wetted parts

Process fitting

316L, PVDF, Duplex steel (1.4462), PEEK

Diaphragm

Sapphire-ceramic

(> 99.9 % Al

ceramic)

Measuring cell seal

FKM (VP2/A), EPDM (A+P 70.10-02), FFKM (Perlast

G74S)

Seal for process fitting (in the scope of delivery)

Ʋ Thread G½ (EN 837), thread G½

inside G¼ (ISO 228-1), thread G½

inside 11.4 mm (ISO 228-1), thread

M20 x 1.5 (EN 837), thread G1½

(DIN 3852-A)

Klingersil C-4400

Ʋ Further thread versions

Depending on the configuration

Materials for applications in foodstuffs
Surface quality, hygienic fittings, typ.

Ʋ Process fitting

< 0.8 µm

Ʋ Ceramic diaphragm

< 0.5 µm

Materials, non-wetted parts

Electronics housing

316L

Plug connector according to ISO 4400

Ʋ Contact, housing plug

PBT/PC

Ʋ Housing connector plug

Ʋ Lid screw

StSt

Ʋ Contact surface

German silver

Ʋ Plug seal

Silicone

Direct cable outlet

Ʋ Cable enclosure

PBT/PC, 1.4404

Ʋ Cable

PUR

Weight

approx. 0.25 kg (0.55 lbs)

Torques

Max. torque for process fitting (examples)

Ʋ Thread G½, inside G¼ (ISO 228-1),

PVDF

5 Nm (3.688 lbf ft)

Summary of Contents for VEGABAR 28

























































Search results

Summary of Contents for VEGABAR 28

Reviews:

Brands by name

Popular brands

Vega VEGABAR 28, Operating Instructions Manual

Search results

Summary of Contents for VEGABAR 28

Reviews:

Brands by name

Popular brands