background image

Introduction

Before Turning Off Power

3

Before Turning Off Power

Before powering off the console perform a system backup:

1.

Beneath the left side of the 450 Plus console, locate the USB Module and insert the V-R Backup thumb drive, 
minimum 4 GB, (P/N 332970-004) into one of the external USB ports on the USB card, P/N 333477-001 
(see item 3 in Figure 1).

Figure 1.  USB board - USB ports

2.

From the Home Screen touch 

Menu > Software Upgrade > DB Backup

 to view the Database Backup 

Screen (see Figure 2). Touch the down arrow in the Backup Destination field to select the Backup thumb drive 
inserted in Step 1, then follow the on-screen instructions to backup TLS-450PLUS console data.

Figure 2.  DB Backup Screen

3.

Turn off, tag and lockout the breaker that supplies power to the console. 

LEGEND FOR NUMBERED BOXES IN 

Figure 1

1. Front of console
2. Ethernet Interface Module
3. USB Ports on USB Module

3

2

1

System Status

07/20/2013 09:10 AM

0 Warning(s)
0 Alarms(s)

Print (0)

Home

Favorites

Menu

Actions

Software Upgrade

Current Version

Available Version

Current Operations

Backup Destination

Version

1.gB 230.4

Not available

Select a source to retrieve versions available

IDLE

DB Backup

Select destination device

OFF

Summary of Contents for TLS-450PLUS

















Reviews: