background image

 

 

 

TCY-T0121 Intelligent Compact Controller

 

  

Version: 2004-07 

[email protected] 

Page 1/12 

 
 
 
 

 

 

 

 

TCY-T0121  
Intelligent Compact Controller 

Features 

• 

Temperature control for 2-pipe, 4-pipe HVAC systems. Temperature range from –40 to 140 °C. 

• 

1 independent PI and On/Off control loop to control temperature. 

• 

1 independent PI and On/Off control loop to control humidity and pressure systems. 

• 

1 modulating output for DC 0...10V or 0…20 mA actuators. 

• 

1 TRIAC controlled floating output 24V AC (2 digital outputs) 

• 

1 Input for DC 0…5V, 0…10V or 0…20 mA sensors 

• 

Temperature sensor analog output for building automation system 

• 

Internal or external passive temperature sensor, selectable by switch 

• 

Transformation of display value according to analog sensor range 

• 

Password protected programmable user and control parameters 

• 

Display and operation unit available in various designs and materials.  

Applications 

• 

Air Only Systems: Constant or Variable Air Volume systems for single or dual duct systems with options of: 

up to two reheat stages 

supply air, extract air cascade control 

humidity control 

Control for variable speed fans 

• 

Air/Water Systems:  

Fan Coil units for 2-pipe or 4-pipe systems with options of: 

§ 

Humidity control 

§ 

Pressure control  

radiator control, chilled ceiling 

• 

Water Only Systems: Radiator, floor heating or chilled ceilings 

• 

Individual room control for hotel rooms, meeting rooms, etc.  

Summary of Contents for TCY-T0121













Reviews: