background image

 

 

 

Veco SpA 

Installation Manual 

Page 3 / 13 

 

1.

 

Introduction 

1.1.

 

General information 

Thank you for purchasing a Climma CWS system! 
This  manual  will  provide  necessary  information  for  the  proper  installation,  operation,  and 
maintenance of your Climma system.  
Climma products are designed and produced to the highest standards and they are all tested in the 
factory. If your Climma system is used according to the guidelines in this manual, it will guarantee 
you trouble free operation for many years. 
If you require assistance, please contact one of our many authorized service centers. To find the 
service center please check our website 

www.veco.net

 or write us at 

[email protected]

 

1.2.

 

System features 

The new Climma C-TOUCH thermostats has been designed to be easy to use and simple, to get the 
best out of your climate control.  

 

Weekly scheduler 

 

Customizable interfaces and colors 

 

Easy interface 

 

Designed for the most used cover plates 

 

Lcd display 2,4’ (320x240 px)

 

 

C-TOUCH  is  compatible  with  Climma  self-contain  Compact  units  (serie  Mk3  and  EF,  with  MK3 
electronic  control)  and  with  Climma  fancoils  (with  Mv8  electronic  control  and  MCON  electronic 
control). 
C-TOUCH  can  fully  replace  Mk3  controls  and Mk2  controls,  considering  that  the  Mk3  and    Mk2 
controls needs a 4 position cutout, while C-Touch only a 3 position. While replacing the control, 
make sure to order the adjusting kit from 4 to 3 positions. 
C-Touch display is also compatible with the following cover plates: 

 

 
The  unit  has  to  be installed by  an  authorized  Climma  service  center  and  in  compliance with  the 
instructions  given  in  this  manual.    A  bad  installation  or  a  misunderstanding  of  the  display 
functioning may result in possible problems and wrong functioning of the system. 

Brand

Serie

Veco Code

Plaque code

Cut on support

BTICINO

LIVINGLIGHT

MPACT001

LNA4803**, LNB4803**, L4803**

Yes

BTICINO

AXOLUTE 

MPACT001

HA4803** / HB4803**

Yes

VIMAR

ARKE'

MPACT001

Arkè 3 position plaque

No

VIMAR

EIKON EVO

MPACT001

Eikon 3 position plaque (BS type excluded)

Yes

VIMAR

EIKON EXE'

MPACT001

Eikon 3 position plaque (BS type excluded)

Yes

VIMAR

PLANA

MPACT001

Plana 3 position plaque

No

BTICINO

AIR (LIVINGLIGHT AIR)

MPACT101

LNC4803** 

Yes

BTICINO

AIR (AXOLUTE AIR)

MPACT201

HW4803**

Yes

VIMAR

IDEA

MPACT301

167*3 (vimar Idea 3 modules)

No

Summary of Contents for Climma C-TOUCH














Reviews: