Vax ONE PWR CORDLESS GLIDE CLHF-GLBS User Manual Download Page 13

13

support.vax.co.uk

CLEANING & MAINTENANCE

Press the brushroll cover button and 

pull to open the cover.

Unhook the brushroll cover and 

remove.

To remove the brushroll, pull the tab 

on the end and remove from the 

brushroll housing. 

IMPORTANT: Make sure both the brushroll and brushroll cover are fitted correctly. If fitted incorrectly 

this may cause poor water pick up. For best cleaning results, advanced cleaning of the brushroll 

should be done every 5-6 uses. For prolonged storage, the brushroll should be removed, cleaned and 

stored in the rinse/storage tray.

REMOVING AND ADVANCED CLEANING OF THE BRUSHROLL

Rinse the brushroll in water (40˚ max) 

and allow to dry before refitting.

The brushroll can be dried and stored 

in the rinse/storage tray.

Clean the brushroll housing and 

brushroll cover of any dirt and debris.

CAUTION: If the brushroll has been obstructed, the brushroll motor protection sensor may have 

been activated. The brushroll will stop, the light on the handle will flash white and the machine may 

switch off. To reset, remove the brushroll and clear any obstruction. Wait 1 minute before refitting the 

brushroll, switch the machine on and recline.

40°C

MAX

Summary of Contents for ONE PWR CORDLESS GLIDE CLHF-GLBS
















Reviews: