manualshive.com logo in svg

Vaux Electronics Aris 700, Manual

Share
Download
Vaux Electronics Aris 700 Manual Download Page 62

MAINTENANCE AND SERVICE

Maintenance

The Aris MediaMation System is designed to be maintenance-free, but it does contain sensitive electronic

parts.  Treat it with care to assure best performance.

Avoid Rough Treatment:

  Avoid dropping the Aris Controller.  If you must ship the system, use the original

packaging (or equivalent) for protection.

Cleaning:  

The hard plastic and aluminum enclosure of the Aris System has a durable finish that should retain

its luster for many years.  Clean exposed parts with a soft, slightly damp soft cloth.  Never use detergents,

excess water, treated cloths, harsh cleaning agents, or sprays.

Service

The Federal Communications Commission (FCC) requires this product be serviced only by the manufacturer

or its authorized service agents.  For instructions on how to obtain service, refer to the warranty included in

this manual or call the Vaux Electronics Service Department at (602) 813-8577.

Attach your sales receipt to this manual for future reference and write down the date this product was

purchased on page 2 of this manual.  This information will be valuable if service should be required during

the warranty period.

According to some State laws, in the event service should be required, you may need both Model and Serial

Numbers.  Please record your Serial Number(s) on page 2 of this manual.  The Aris Controller Serial Number

can be found on the rear panel.

LIMITED WARRANTY

What does your warranty cover?

•  Any defect in material or workmanship.

For how long after the original purchase?

•   Three-year limited warranty on the Aris Controller.   Vaux Remote Controls have a one-year limited

warranty.

What will we do?

•  If your Aris System is defective and returned within 30 days of the date it was purchased, we will replace

it at no charge to you.

•  If your Aris System is returned after 30 days, but within the three years of the date of purchase, we will

repair it, or, at our option, replace it at no charge to you.  If we repair your Aris System , we may use new or

reconditioned replacement parts.  If we choose to replace your Aris System, we may replace it with a new or

reconditioned unit of the same or similar design.

•  The repair or replacement unit will be warranted for either (a) 90 days or (b) the remainder of the original

three year warranty period, whichever is longer.

62

Summary of Contents for Aris 700
































































Reviews:

No comments

Brands by name

Popular brands

Load more brands