Vaux Electronics Aris 700 Manual Download Page 3

Page: 3 / 63

CONTENTS

Important Safety Information ............................................................................ 4

Introduction....................................................................................................... 5

Aris Model Comparison Chart ........................................................................... 6

Parts Checklist .................................................................................................. 7

Aris MediaMation Controller Front Panel .......................................................... 8

Aris MediaMation Controller Rear Panel ............................................................. 9

Overview of the RC-8 Remote Control ............................................................. 10

Overview of the KP-1 Wired/Wireless Keypads ...............................................

Designing the System ......................................................................................

Infrared Learning Memory Layout ................................................

IR Programming Considerations ..................................................

The Source-Selection Process........................................................

Auto-Source-Power Option ..........................................................

Power-On-Delay and Power-Off-Delay .......................................... 17

Power State Incorrect? .................................................................

Auto-Receiver-Power Option .......................................................

Auto-TV-Power Option ................................................................

A/V-Source-Definition for Auto-TV-Powering ..............................

System-Active-PLC-Power Option .................................................

Auto-PLC-Zone-Power Option ......................................................

Auto-PLC-Source-Power Option ...................................................

Source-Select MACRO Programming Considerations ..................

X-10 Input (2-way X-10) ............................................................... 20

Hardware Installation ........................................................................................ 21

Programming the System ................................................................................... 25

Program Default Audio/Video Zone .............................................

Program Default Lighting Group (House Code) ..........................

Infrared Learning ........................................................................

MACRO Programming .................................................................

Adjusting Zone Maximum and Turn-On Volume Levels ...............

System Operation .............................................................................................. 33

The RC-8 Remote Control ...........................................................

Audio/Video Control ....................................................................

Lighting and Appliance (X-10®) Control .....................................

MACRO Operation .....................................................................

Appendix 1: Programming Tables ..................................................................... 41

Appendix 2: Device/Zone-Specific IR Outputs .................................................

Appendix 3: RF Range and Antenna Options .................................................... 46

Appendix 4: Audio and Video Wiring Considerations .......................................

Appendix 5: 710/720i IR Input and use of IR-Learning Keypads ...................... 52

Appendix 6: Computer-Programmable Features ............................................... 53

Appendix 7: Multiple-Controller Installations ................................................... 55

Appendix 8: VauxSerial RS-232 Port ................................................................. 57

Appendix 9: Updating System Software ........................................................... 58

Appendix 10: Troubleshooting Guide .............................................................. 60

Maintenance and Service; Warranty .................................................................. 62

Summary of Contents for Aris 700
































































Search results

Summary of Contents for Aris 700

Reviews:

Brands by name

Popular brands

Vaux Electronics Aris 700, Manual

Search results

Summary of Contents for Aris 700

Reviews:

Brands by name

Popular brands