background image

  1 YEAR LIMITED WARRANTY

Express and Exclusive Limited  Warranty to Original Retail Buyer

Every ALLTRADE® product is inspected before leaving the factory . This product is warranted to be free of defects 
in material and workmanship for a period of one year from the date of original purchase . If a defect appears within 
one year after the date of purchase, the purchaser may return the item, together with a purchase receipt or other 
appropriate proof of purchase to the place of purchase . Upon receipt of the item(s), the place of purchase will, at its 
option, replace the defective item or refund your money . This warranty shall not apply when the product has been 
used for commercial or rental purposes, has been tampered with, when repairs or attempted repairs have been made 
by unauthorized persons, or where the item has been subjected to misuse, abuse, accident or damage in transit . No 
charges will be accepted for unauthorized parts, repairs or services . 

IN NO EVENT SHALL ALLTRADE BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES. 

Some provinces do not allow limitations on how long an implied warranty lasts and some states do not allow the 
exclusion or limitation of the incidental or consequential damages, so part or all of the above limitations or exclusions 
may not apply to you . This warranty gives you specific legal rights, and you may also have other rights which vary 
from province to province .

FCC INFORMATION 

Warning: Changes or modifications to this unit not expressly approved by the party responsible for 

compliance could void the user’s authority to operate the equipment.
NOTE: 

This equipment has been tested and found to comply with the limits for Class B digital device, pursuant to 

part 15 of the FCC Rules . These limits are designed to provide reasonable protection against harmful interference in 

a residential installation . This equipment generates, uses and can radiate radio frequency energy and, if not installed 

and used in accordance with the instructions, may cause harmful interference to radio or television reception, which 

can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by 

one or more of the following measures:
- Reorient or relocate the receiving antenna . 

- Increase the separation between the equipment and the receiver . 

- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected . 

- Consult the dealer or an experienced radio/TV technician for help .

This device complies with Part 15 of the FCC Rules . 

Operation is subject to the following two conditions: 

(1) This device may not cause harmful interference, and 

(2)  This device must accept any interference received, including interference that may cause undesired operation .

10

Summary of Contents for 240022













Reviews: