Vatech PHT-30CSS Installation Manual Download Page 6

Page: 6 / 162

Important Notes

vatech A9 (Model:PHT-30CSS) Installation Manual

Important Notes

The sudden temperature changes inside of the X-ray room may cause

condensation. Ensure to keep the inside temperature constant at least for

an hour before turning on the equipment.
Ensure to install the equipment on flat ground. If the equipment is not

installed parallel to the ground, it may fall or tilt, causing a physical injury,

property damage, or system malfunction.
DO NOT push or pull the equipment.
Only VATECH-authorized technician shall install the equipment,

complying with the proper procedures and regulations stated in this

manual.
Failure to read and understand this manual's information may cause a

physical injury, property damage, or equipment failure. Please read each

chapter thoroughly before attempting any of the installation procedures.

Summary of Contents for PHT-30CSS



































































































































































Search results

Summary of Contents for PHT-30CSS

Reviews:

Related manuals for PHT-30CSS

Brands by name

Popular brands

Vatech PHT-30CSS, Installation Manual

Search results

Summary of Contents for PHT-30CSS

Reviews:

Related manuals for PHT-30CSS

Brands by name

Popular brands