background image

OPERATION AND MAINTENANCE MANUAL 

MAC QM MOTORS 

 

 

 

 

 

 

 

 

 

 

 

PAGE: 35

 

 

 

                  

 

 

CODE: CTT42  EDITION: 01  RELEASE: JULY 2016 

Subject to technical changes without prior notice

 

 

5.

 

INSTALLATION AND START-UP 

 

PRECAUTION 
Damage caused to bearings as a result of long storage periods 

 

If the machine has been stored for more than 3 years in good conditions (dry, dust-free place, etc.), the grease on the bearings 
must be  changed,  if  they  need  re-greasing,  or  the  bearing  should  be  changed  if  it  is  a bearing  with  lubrication  for its  entire 
service life. If the machine has been stored in poor conditions, the change or re-greasing of the bearings may be necessary 
before the aforementioned period.   
 
The following describes the conditions that are necessary for the installation and start-up of the machine. 

5.1

 

Motor installation 

 

5.1.1

 

Site 

A correct site is essential for guaranteeing a long motor service life. The use of the motor in an incorrect site could shorten its 

service life considerably. The following are some points to bear in mind when choosing the correct site for the motor: 

 

a)

 

 The chosen site must comply with the ambient temperature range and altitude for which the motor was selected (for 

more details, see section 3.5.3).  

 

 

HOT SURFACE 

The exterior surface of the motors can reach temperatures of more than 60°C and, therefore, the appropriate precautions must 

be taken to avoid accidental contact (the motor bears a plate indicating said circumstance). 
 

b)

 

The site must have a humidity level of less than 85% to prevent condensation appearing on the surface. If the humidity 

levels at the site exceed 85%, the motor must be fitted with anti-condensation heaters (see section 3.7.6). 

 

c)

 

The air inlet and outlet must not be blocked. There must be no recirculation of hot air from the outlet to the inlet. 

 

PRECAUTION 
Damages caused to the motor by blocking the airflow at motor air-inlet 

 

Damages may be caused to the motor if there is an insufficient airflow at motor air-inlet. If the machine does not have sufficient 

cooling airflow, the windings may overheat and the corresponding consequences may arise. 
 

 

 

Summary of Contents for MAC QM

























































Reviews: