background image

 

 

Panel Mounting Procedure  

1. Cut and drill the panel (refer to panel mount drawing). Measurements are in inches. 

 
Panel Mounting Cutout 

2. If access to the side of the monitor is not available following installation, attach the power and video 

cables to the side of the monitor at this time.  

3. Install the monitor in the prepared cutout. 
4. Install the lock nuts and washers, supplied with the monitor, behind the holes running along the sides 

and top/bottom of the cutout in the panel. Extra lock nuts and washers are provided. 

MOUNTING INSTRUCTIONS

MOUNTING INSTRUCTIONS

 

 

7.1 

Panel Mount Procedure 

14 

Section 

Mechanical Drawings 

Model 

Description 

Page(s) 

VT150P

 

15.0” DiamondVue Panel Mount Mechanical Drawing 

15-16 

VT150R

 

15.0” DiamondVue Rack Mount Mechanical Drawing 

17 

VT150W 

15.0” Wall Mount Mechanical Drawing 

18 

VT150PI 

15.0” Intecolor Configured Mechanical Drawing 

19-20 

 

Note:  

Use #10-32 nuts for mounting.

 

5. Tighten all mounting nuts evenly to a torque of 24 inch-pounds. 

ATTENTION: 

Mounting nuts must be tightened to a torque of 24 inch-pounds to provide panel seal and 

avoid potential damage. Vartech Systems  assumes no responsibility for water or chemical damage 
to the monitor or other equipment within the enclosure due to improper installation. 

6. Attach the power and video cables to the side of the monitor if  you have not already done so.  

Summary of Contents for DiamondVue VT150P



















Reviews: