background image

For the user

21

Värmebaronen Vedolux 55

Tar and and a lot of soot 
in the tubes.

Incorrect combustion.

See the item about high flue gas temperature.

Incorrect connection.

Check.

Heat is not transferred 
from the boiler to the 
accumulator.

Circulation pump too small.

The pump must have sufficient capacity so that it can 
transfer the heat. Replace with a bigger pump.

Air.

Our suggested connection is not air-sensitive. Vent.

Incorrect accumulator 
connection.

See points above.

Boiling sound in the boiler. Low pressure head.

Check the pressure, should be > 14.5 psi. The expansion 
tank must be adapted to the volume and the temperature 
variations that occur.

Fan does not start

Switches in position O.

Switch the switches to position I.

Forgot to connect the quick 
connector.

Connect the quick connector.

Overheating protection 
triggered.

Reset the overheating protection.

Safety valve opens when 
the temperature of the 
system increases.

Expansion tank too small.

See the 'Expansion system' section.

Prepressurisation in the 
expansion tank too high/low.

Check the pressure in the tank. See 'Expansion system'.

Summary of Contents for Vedolux 55

























Reviews: