background image

13

Part

Action

Frequency

Note

Bowl screen

Check the safety of the bowl screen: 

Does the tool stop rotating when the 

screen is tilted/removed?

Regularly

 

If the tool does not immediately 

stop  rotating  on  tilting/removal  of 

the  screen,  the  machine  must  not 

be used.

Call the engineer

Emergency stop

Test the emergency stop: Does the tool 

stop rotating when the emergency stop 

is activated?

Regularly

 

If  the  tool  does  not  immedia

-

tely stop rotating on activation of the 

emergency  stop,  the  machine  must 

not be used.

Call the engineer

Mixer head

The mixer head should only be lubri

-

cated on repair, see the section 

“Lub-

rication and grease types”

.

During repairs

The machine’s 

other moving 

parts

The moving parts that belong to the 

bowl’s  lifting  mechanism  all  run  in 

maintenance-free plain bearings and 

should not therefore be lubricated.

Never

Attachment drive

The rubber plug for covering the open

-

ing of the attachment drive should be 

on the machine and be intact.

Daily

The rubber plug must cover the 

opening  on  the  attachment  drive 

when the latter is not in use

.

Cleaning

Follow the instructions in the section 

“Cleaning”

Follow  the  instructions 

in the section “Cleaning”

s

ystematiC

 

maintenanCe

:

r

eadinG

 

the

 

maChines

 

data

:

Press the stop button for 5 sec. The machine’s data will then be displayed as alternating text in the display. There are five 

readings corresponding to the five data sets described below:

• 

Data set 1: 

States firmware version, displayed as “F” followed by three figures, e.g. 

 = firmware version 3.

• 

Data set 2

: States the machine’s running time, displayed as “t” followed by three figures, which indicate the number of 

9.999-minute cycles, e.g. 

= 2 x 9.999 min., or 19.998 min.

• 

Data set 3

: Displays four figures, which indicate the number of minutes the current cycle has been running, e.g. 

 = 

1.234 min.I.e., if 

 is displayed followed by 

, the machine has been running for 19.998 min. + 1.234 min., 

or a total running time of 21.232 min.

• 

Data set 4

: States the number of times the machine has been disconnected from the power supply (plug pulled out of the 

machine/powercut/switched off) and restarted, displayed as “r” followed by three figures, which indicate the number of restarts, 
e.g. 

 = 2 x 9,999 restarts, or 19,998 restarts.

• 

Data set 5

: Displays four figures, which indicate the number of restarts which have happened in the current cycle, e.g.

 

= 1234 times. In other words, if 

 is displayed followed by 

 , the machine has restarted a total of 19,998 + 

1,234 times, or 21,232 times.

r

eadinG

 

the

 

error

 

loG

:

It is possible to display a log of the errors that have occurred:
•  Hit emergency stop and press 

 next to 

•  The display shows the latest error first.
•  To scroll back through the errors, press 

 next to 

; to scroll forward, press 

 next to 

.

•  The last eight errors can be displayed.
•  Deactivate emergency stop to cancel the display

Summary of Contents for V20K





































Reviews: