background image

MVS-1C 

Page 2 

This guide will inform the electrician on proper wiring and installation procedures 
and, will also inform the user on how to use the MVS-1C controller. 

The  manufacturer  recommends  that  the  following  installation  instructions  be 
followed to  as closely  as possible, and that all work be performed by  a certified 
electrician. Failure to do so may void the warranty. 

Description

 

The MVS-1C controller is designed to manually control a variable speed output. 

Speed Selector

 is used to adjust the speed of the variable output. That 

Speed 

Selector  can  also  turn  off  the  output  by  turning  it  counter-clockwise.  The 
controller operates on 115/230V and 50/60Hz.  

The  MVS-1C  comes  in  a  PVC  non-corrosive  enclosure  that  is  protected  from 
dust and humidity. The MVS-1C is covered by a complete two-year warranty. 

Unpacking 

Unpack  the  MVS-1C  module  and  inspect  contents  for  damage.  Should  the 
contents  appear  to  be  damaged,  contact  your  local  distributor  to  return  the 
equipment. 

The package should contain the following standard items: 
1 MVS-1C 
1 Mounting Plate Kit 
1 Installation / User’s guide 

Mounting hardware required 

This is the list of the mounting hardware needed, which is not included with the 
product: 

Screws (to mount the module on the wall) 
Screwdriver 
Soldering iron kit or approved sealed connectors 

www.monitrol.com

Summary of Contents for MVS-1C











Reviews: